The UART controller used in the A10/A13 is the Synopsys DesignWare 8250.
The wrong use of a regular 8250 driver may lead to a oops during kernel
boot with "irq 17: nobody cared", because the apb UART as an extra
interrupt that gets raised when writing to the LCR when busy.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pull x86 fixes from Peter Anvin:
"This is mainly a workaround for a bug in Sandy Bridge graphics which
causes corruption of certain memory pages."
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/Sandy Bridge: Sandy Bridge workaround depends on CONFIG_PCI
x86/Sandy Bridge: mark arrays in __init functions as __initconst
x86/Sandy Bridge: reserve pages when integrated graphics is present
x86, efi: correct precedence of operators in setup_efi_pci
We currently use a temporary 1MB section aligned to a 1MB boundary for
mapping the provided device tree until the final page table is created.
However, if the device tree happens to cross that 1MB boundary, the end
of it remains unmapped and the kernel crashes when it attempts to access
it. Given no restriction on the location of that DTB, it could end up
with only a few bytes mapped at the end of a section.
Solve this issue by mapping two consecutive sections.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Tomasz Figa <t.figa@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patrik Kluba reports that the preempt count becomes invalid due
to the preempt_enable() call being unbalanced with a
preempt_disable() call in the vfp assembly routines. This happens
because preempt_enable() and preempt_disable() update preempt
counts under PREEMPT_COUNT=y but the vfp assembly routines do so
under PREEMPT=y. In a configuration where PREEMPT=n and
DEBUG_ATOMIC_SLEEP=y, PREEMPT_COUNT=y and so the preempt_enable()
call in VFP_bounce() keeps subtracting from the preempt count
until it goes negative.
Fix this by always using PREEMPT_COUNT to decided when to update
preempt counts in the ARM assembly code.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reported-by: Patrik Kluba <pkluba@dension.com>
Tested-by: Patrik Kluba <pkluba@dension.com>
Cc: <stable@vger.kernel.org> # 2.6.30
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Kconfig items BCM47XX_BCMA and BCM47XX_SSB selected respectively
BCMA_DRIVER_GPIO and SSB_DRIVER_GPIO. These options depend on GPIOLIB
without explicitly selecting it so it results in a warning when GPIOLIB
is not set:
scripts/kconfig/conf --oldconfig Kconfig
warning: (BCM47XX_BCMA) selects BCMA_DRIVER_GPIO ... unmet direct
dependencies (BCMA_POSSIBLE && BCMA && GPIOLIB)
warning: (BCM47XX_SSB) selects SSB_DRIVER_GPIO ... unmet direct
dependencies (SSB_POSSIBLE && SSB && GPIOLIB)
which subsequently results in compile errors.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4759/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In the printk, the variable t euqals to NULL, so there is no t->index.
Use v->tc->index instead.
[ralf@linux-mips.org: Use opportunity of changing this line anyway to make
this line whitespacely correct.]
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4792/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Converting a 64 Bit TOD format value to nanoseconds means that the value
must be divided by 4.096. In order to achieve that we multiply with 125
and divide by 512.
When used within sched_clock() this triggers an overflow after appr.
417 days. Resulting in a sched_clock() return value that is much smaller
than previously and therefore may cause all sort of weird things in
subsystems that rely on a monotonic sched_clock() behaviour.
To fix this implement a tod_to_ns() helper function which converts TOD
values without overflow and call this function from both places that
open coded the conversion: sched_clock() and kvm_s390_handle_wait().
Cc: stable@kernel.org
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
FSI - DA7210 needs amixer settings to use it.
This patch adds quick setting guide
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reverts commit 41bd956de3.
The fix is incorrect and not appropiate for the latest kernels.
In fact it _causes_ the BUG: scheduling while atomic while
doing vCPU hotplug.
Suggested-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQxqj1AAoJEHm+PkMAQRiG9MQH/j21UwP2QGpdpXbWAnFMjtlv
uE/yCFhPoqR1QjjE6oRlO6MHFA41xGDbr5RQki9Ik2AfSYiastt4ZWYvtSJKVTCr
O0Lj+Cdt/2qBkGiARHqVEBZ4S/l/cw4/EHPb5StFyu3ggnPPQhoPIP7oAmRn0+mh
NNb5CEcJOLqIaJSteqMP71Q899ncbLayBnimYCaC2f6r00beqNXIqxSHipcPlUsf
ehNxqCX+5z5Q788EL33EL8GpBcy4Ueevu6nvnuVI8qIEnBnrBVngsiaQ4Hti+2eK
A//4DYoF2N1wLjQv7hFeiwMURQ16OlxXoc/Z66sv2QQRwPxOIQlxdhWuey4KebA=
=7LYr
-----END PGP SIGNATURE-----
Merge tag 'v3.7' into stable/for-linus-3.8
Linux 3.7
* tag 'v3.7': (833 commits)
Linux 3.7
Input: matrix-keymap - provide proper module license
Revert "revert "Revert "mm: remove __GFP_NO_KSWAPD""" and associated damage
ipv4: ip_check_defrag must not modify skb before unsharing
Revert "mm: avoid waking kswapd for THP allocations when compaction is deferred or contended"
inet_diag: validate port comparison byte code to prevent unsafe reads
inet_diag: avoid unsafe and nonsensical prefix matches in inet_diag_bc_run()
inet_diag: validate byte code to prevent oops in inet_diag_bc_run()
inet_diag: fix oops for IPv4 AF_INET6 TCP SYN-RECV state
mm: vmscan: fix inappropriate zone congestion clearing
vfs: fix O_DIRECT read past end of block device
net: gro: fix possible panic in skb_gro_receive()
tcp: bug fix Fast Open client retransmission
tmpfs: fix shared mempolicy leak
mm: vmscan: do not keep kswapd looping forever due to individual uncompactable zones
mm: compaction: validate pfn range passed to isolate_freepages_block
mmc: sh-mmcif: avoid oops on spurious interrupts (second try)
Revert misapplied "mmc: sh-mmcif: avoid oops on spurious interrupts"
mmc: sdhci-s3c: fix missing clock for gpio card-detect
lib/Makefile: Fix oid_registry build dependency
...
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Conflicts:
arch/arm/xen/enlighten.c
drivers/xen/Makefile
[We need to have the v3.7 base as the 'for-3.8' was based off v3.7-rc3
and there are some patches in v3.7-rc6 that we to have in our branch]
!CONFIG_SMP build, two patches fixing broken imxfb driver caused by
multiplatform conversion, and a couple of pm/hotplug fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ9Vu/AAoJEFBXWFqHsHzOMJ0H/jqHG4aQ8TA2ve2Ax/DWDQCW
vUszc6HnBg3xJM7f4LaCED6UC5Q8H8h5yjdZN8Uy4h63AhGFz85F+9CUO8/Puxf8
e6HiffFL578S6ienfiLYPLsHmbFIvH0Wr+0f3+x0Wa2I+AxjD7xHLqNb/akj8MAN
kYw6O6WwYtufl+1y8l6/Hq+3MVRvos/7I6wid7ADi96C8zIt1nFUW5RN4e0uk2Pk
TCHZEXzkKUyvytaaSOAh1zVRnJOAD4Y+qGSGeGMYQTIuEfNUGAmMwhpI59neNGpb
6LdGzG27xNR0r3OhnrTFqaZgGwDdsU4AqE/RXfi5AmWStanKF29QqW+0HgAv+Zk=
=3LfO
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.8-2' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
It's the second batch of fixes for 3.8, which includes one fixing for
!CONFIG_SMP build, two patches fixing broken imxfb driver caused by
multiplatform conversion, and a couple of pm/hotplug fixes.
* tag 'imx-fixes-3.8-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: correct low-power mode setting
ARM: imx: disable cpu in .cpu_kill hook
video: imxfb: fix imxfb_info configuration order
ARM: imx: platform-imx-fb: modifies platform device name
ARM: imx: fix build error with !CONFIG_SMP
Signed-off-by: Olof Johansson <olof@lixom.net>
There have been a number of new syscalls introduced to arch/arm/ since
the compat layer was implemented for arm64, so add pointers to the
relevant functions to the compat syscall table.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Due to a series of problems with the handling of Atmel, a combination of
making changes that make other branches instantly buggy and a general
failure to deal with the resulting issues effectively, v3.8 Atmel audio
currently won't work at all for DT boards without adding pinctrl
definitions and a request for those.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=W+cl
-----END PGP SIGNATURE-----
Merge tag 'asoc-atmel-pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: atmel: Fixes for pinctrl
Due to a series of problems with the handling of Atmel, a combination of
making changes that make other branches instantly buggy and a general
failure to deal with the resulting issues effectively, v3.8 Atmel audio
currently won't work at all for DT boards without adding pinctrl
definitions and a request for those.
2 fixes to prevent unconditional re-compile of dts files on arm and arm64.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ9HKkAAoJEMhvYp4jgsXihT0H/RSUuhC02eQV7mkIJwPVROwd
8nbdRAes22g2nbBN0NDDsZ6GCGjVBx/rt1MhS/yhzE6GqKkT+MnpQ+yE3A0xK+BP
bdqYFmajXauHNrPo6jp9HRwui7BKU9GMl2bkN39kALtY35Fo25XaGelsC+ue6KAg
VFA+iuHG9wEaVbYX/77IyTDjSECKbrcfGGlN1WHIIrFjIQDMA7BjoNb9kyT5oS+l
kdS5n5MC1rCeg7lKD1ScVqPye5eOFjk35ZjJEfkfR/dXRsds1/wp17lH4rxC6Fcp
/9eEK3GeYAueQCTyHRDmkUtMGCA9qij0cUjVQkYf7Je6pHdQ5x7/eQXiHcKEv/M=
=cMYU
-----END PGP SIGNATURE-----
Merge tag 'dt-fixes-for-3.8' of git://sources.calxeda.com/kernel/linux
Pull devicetree fixes from Rob Herring:
"Two fixes to prevent unconditional re-compile of dts files on arm and
arm64."
* tag 'dt-fixes-for-3.8' of git://sources.calxeda.com/kernel/linux:
ARM: dts: prevent *.dtb from always being rebuilt
arm64: dts: prevent *.dtb from always being rebuilt
Most of commits found here are for ASoC device specific fixes,
arizona, cs4271, wm5102, wm2200, etc, in addition to a couple of
memory leak fixes in ASoC core.
Other than that, regression fixes in HD-audio and USB-audio, and
a fix for new Realtek codecs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJQ88mfAAoJEGwxgFQ9KSmkbXkP/3NGkP2N7DX6qK9pJ00sR9dY
gMmu0yM+W/jJZ0Xf2yU7x/sZdWrUbtICOZ67cOrG7M9W3DIOzMtvaiMCIh12+LUH
xU1KRPfVe+oLGy6eQBR5o45z4DNNwgNZ9LpKv8/DySrRMJ60hJ4jxJKSnMmTyCe7
vMlp9k1nJP41jkZX1rRW3JrBBSMB9NHWiltm+GIZJ3VKqM3+uiJJZaMAWcjnMiYy
tnVOxomJzNPCxv9Bv2GzgD0MII0G8olYhXeVJP3B76EnNbK6G5PbxmkTp+/oKVQf
fU2Z5FheqqT3mjYeYo++vj0E5Dau+iYU02z0uHMMErUCpKTvwGa2szBH1PPOqcHU
H85EBJ12OQt8vNNpGSKdPBtAqqOJm9C1jcT1387Dubq9Oz2X113Zl7QI3xH5u91s
8lDhJI4XhlDwjSe5SUCHsdIwG4uQM9UOdc8hEJkCMemu2cFQTJUN5mwRJsd9B6Po
ACB231GwNsRRq28nh1AxtroWUlO7exWOpsbqwoF6zuhwtUzR1Vm87Vd4go/T2wTD
Lvyt5rDSnhFHWELkVBTk3/U/6fn0aQ8pR0wuScF1VoQCF1vphlEBWuHUOnorFmd+
gt1T4pp4jc/xmCZLdMXlCcsctPb+5HRVO+DkfCh9RYDvanh8HfgUF/WlhF361qXr
Vu4uLsazWMJSFX/gXTzn
=iVG2
-----END PGP SIGNATURE-----
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Most of commits found here are for ASoC device specific fixes,
arizona, cs4271, wm5102, wm2200, etc, in addition to a couple of
memory leak fixes in ASoC core.
Other than that, regression fixes in HD-audio and USB-audio, and a fix
for new Realtek codecs."
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (30 commits)
ALSA: usb-audio: Fix NULL dereference by access to non-existing substream
ALSA: hda - Add support of new codec ALC284
ALSA: usb-audio: Make ebox44_table static
ALSA: hdspm - Fix wordclock status on AES32
Revert "ALSA: hda - Shut up pins at power-saving mode with Conexnat codecs"
ALSA: hda - Disable runtime D3 for Intel CPT & co
ALSA: pxa27x: fix ac97 warm reset
ALSA: pxa27x: fix ac97 cold reset
ASoC: wm_adsp: Ensure that block writes are from DMA aligned addresses
ASoC: wm2000: Fix sense of speech clarity enable
ASoC: wm5100: Remove DSP B and left justified formats
ASoC: arizona: Remove DSP B and left justified AIF modes
ASoC: wm2200: Remove DSP B and left justified AIF modes
ASoC: wm5102: Improve speaker enable performance
ASoC: core: fix the memory leak in case of remove_aux_dev()
ASoC: core: fix the memory leak in case of device_add() failure
ASoC: cs42l52: Catch no-match case in cs42l52_get_clk
ASoC: lm49453: Update lm49453_reg_defs values as per LM49453 HW revision-B
ASoC: lm49453: Fix adc, mic and sidetone volume ranges
ASoC: arizona: Correct FLL source definitions
...
Pull sparc updates from David Miller:
1) Add finit_module syscall entry.
2) Remove stray __dev{init,exit} references, from Sam Ravnborg.
Fix up conflicts in the sparc PCI code due to whitespace differences in
the __dev{init,exit} removal (which also came in through Greg).
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc: remove __devinit, __devexit annotations
sparc: Hook up finit_module syscall.
The hardware reset value of bit CCM_CLPCR_LPM enables WAIT mode
(WAIT_UNCLOCKED) by default. However this is undesirable because
WAIT mode should only be enabled when there is a driver managing
ARM clock gating. Correct the initial power mode to WAIT_CLOCKED
(disable WAIT mode). While at it, the power mode after resuming
is also set back to WAIT_CLOCKED from STOP_POWER_OFF.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It's buggy to disable the cpu that is being hot-unplugged in .cpu_die
hook which runs on the cpu itself. Instead, it should be done in
.cpu_kill which runs on the thread (another cpu) that asks for shutting
down the cpu. Move imx_enable_cpu(cpu, false) call into .cpu_kill
hook, and leave the cpu to be hot-unplugged in WFI within .cpu_die,
so that we can get a more stable cpu hot-plug operation.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
if_changed (used by the *.dts->*.dtc rule) rebuilds files if they aren't
contained in $(targets). (make V=2 indicates this). Add $(dtb-y) to
$(targets) to prevent *.dtb from always being rebuilt.
This fixes a regression introduced by the .dtb rule rework in 499cd82
"ARM: dt: change .dtb build rules to build in dts directory".
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
if_changed (used by the *.dts->*.dtc rule) rebuilds files if they aren't
contained in $(targets). (make V=2 indicates this). Add $(dtb-y) to
$(targets) to prevent *.dtb from always being rebuilt. Note
This fixes a regression introduced by the .dtb rule rework in da4cbc6
"arm64: use new common dtc rule", although since arm64 doesn't actually
have any *.dts yet, this isn't a critical issue.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Somewhere along the line the ebss label was taken out, resulting in pcrel
branch too far errors. Restore the label to get things building again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
early_pci_allowed() and read_pci_config_16() are only available if
CONFIG_PCI is defined.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Framebuffer platform device is now identified by a device id (imx1-fb or
imx21-fb) instead of by driver name (imx-fb).
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
__devinit, __devexit annotations are nops - so drop them.
Likewise for __devexit_p.
Adjusted alignment of arguments when needed.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xfs module uses a lot of tracepoint, with TRACEPOINTS=y and a
few debugging options the GOT table of the xfs module will get
bigger than 4K. To get a working xfs module it needs to be compiled
with -fPIC instead of -fpic. To play safe use -fPIC for all modules.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The pfn calculation in pmd_pfn() is broken for thp, because it uses
HPAGE_SHIFT instead of the normal PAGE_SHIFT. This is fixed by removing
the distinction between thp and normal pmds in that function, and always
using PAGE_SHIFT.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add pinctrl support for SSC on AT91 dtsi files.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[nicolas.ferre@atmel.com: split dtsi and driver changes]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reluctantly-acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
mn10300 doesn't provide its own atomic64 implementation, so it should pull
in the generic one.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SNB graphics devices have a bug that prevent them from accessing certain
memory ranges, namely anything below 1M and in the pages listed in the
table. So reserve those at boot if set detect a SNB gfx device on the
CPU to avoid GPU hangs.
Stephane Marchesin had a similar patch to the page allocator awhile
back, but rather than reserving pages up front, it leaked them at
allocation time.
[ hpa: made a number of stylistic changes, marked arrays as static
const, and made less verbose; use "memblock=debug" for full
verbosity. ]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Some systems compile in both ARMv6 and ARMv7 into multiplatform
configurations. This means the default compiler flags are for ARMv6,
and we will get:
arch/arm/mach-mvebu/coherency_ll.S: Assembler messages:
arch/arm/mach-mvebu/coherency_ll.S:45: Error: selected processor does not support `dsb'
Fix this by specifying ARMv7 flags for coherency_ll.o.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Integrator/AP syscon remapping was done in the .setup()
function rather than .preinit() which is wrong - .preinit()
is called before .setup() and the former also use the syscon
base and cause a crash since it was not yet remapped.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
- gpio fixes in mvebu, kirkwood, and dove
- small DT fix for mvebu (correct RAM size)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQ7xPtAAoJEAi3KVZQDZAeYBEH/0fxDNyDyRxxTYhf0FgfJpOW
kknx5d6XzL75HQCvFD0ObEkgmxkWNCnkUqU5ZglqGx7/P5yKs8K46IyG1LHF2mnL
4/TSJH7QOLTcI5DrLtvgbhLDQjqibtxGC0IGucbHxO/9unn8uk5xV7ax5++JcTQb
p8vhldxUa1QJu9og6SJRL+LJnI9PdcXpZELCdZOyPd62/9MNCb7uZwRRC0sIDk7N
0SsJ/81VUmq0o29WkZtWrxqPiUUzgsyAnC4anVeGjBn/PzcY63pzY4lpNEu94WLp
Ed9s8E/UcyltjcOHADWfOzNehGQjQwpVI9NdyOFgF/QMVJItHwfuXe1Rra9Qu50=
=8ARJ
-----END PGP SIGNATURE-----
Merge tag 'mvebu_fixes_for_v3.8-rc3' of git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
mvebu fixes for v3.8-rc3
- gpio fixes in mvebu, kirkwood, and dove
- small DT fix for mvebu (correct RAM size)
* tag 'mvebu_fixes_for_v3.8-rc3' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: Fix memory size for Armada 370 DB
ARM: Dove: add Cubox sdhci card detect gpio
ARM: Kirkwood: fix ns2 gpios by converting to pinctrl
arm: mvebu: use global interrupts for GPIOs on Armada XP
Commit 68b2532 (ARM: imx: select HAVE_IMX_SRC when SMP is enabled)
introduces a build error with imx_v6_v7_defconfig when CONFIG_SMP is
deselected.
LINK vmlinux
LD vmlinux.o
MODPOST vmlinux.o
GEN .version
CHK include/generated/compile.h
UPD include/generated/compile.h
CC init/version.o
LD init/built-in.o
arch/arm/mach-imx/built-in.o: In function `imx6q_restart':
platform-ahci-imx.c:(.text+0x448c): undefined reference to `imx_src_prepare_restart'
arch/arm/mach-imx/built-in.o: In function `imx6q_pm_enter':
platform-ahci-imx.c:(.text+0x4544): undefined reference to `imx_set_cpu_jump'
arch/arm/mach-imx/built-in.o: In function `imx6q_init_irq':
platform-ahci-imx.c:(.init.text+0xbef0): undefined reference to `imx_src_init'
make[1]: *** [vmlinux] Error 1
While the commit adds 'def_bool y if SMP' for HAVE_IMX_SRC, it should
not remove 'select HAVE_IMX_SRC' from SOC_IMX6Q, as the IMX6Q UP build
also needs HAVE_IMX_SRC. Add the HAVE_IMX_SRC select back for SOC_IMX6Q
to fix above build error.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Ensure that the aux table is properly initialized, even when optional features
are missing. Without this, the FDPIC loader did not work. This was meant to
be included in commit d5ab780305.
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
b4265f1234
(mm: use vm_unmapped_area() on sh architecture)
broke sh boot. This patch define TASK_UNMAPPED_BASE
as a page aligned constant to solve this issue.
Special thanks to Michel
Acked-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
__hyp_stub_install duplicates quite a bit of safe_svcmode_maskall
by forcing the CPU back to SVC. This is unnecessary, as
safe_svcmode_maskall is called just after.
Furthermore, the way we build SPSR_hyp is buggy as we fail to mask
the interrupts, leading to interesting behaviours on TC2 + UEFI.
The fix is to simply remove this code and rely on safe_svcmode_maskall
to do the right thing.
Cc: <stable@vger.kernel.org>
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Reported-by: Harry Liebel <harry.liebel@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Secondary CPUs should use the __hyp_stub_install_secondary entry
point, so boot mode inconsistencies can be detected.
Cc: <stable@vger.kernel.org>
Acked-by: Dave Martin <dave.martin@linaro.org>
Reported-by: Ian Molton <ian.molton@collabora.co.uk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Non-T variants of ARMv4 do not support the bx instruction.
However, __hyp_stub_install is always called from the same
instruction set used to build the bulk of the kernel, so bx should
not be necessary.
This patch uses the traditional "mov pc" instead of bx.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
[will: fixed up remaining bx instruction]
Signed-off-by: Will Deacon <will.deacon@arm.com>
commit b080935c86
kvm: Directly account vtime to system on guest switch
also removed the irq_disable/enable around kvm guest switch, which
is correct in itself. Unfortunately, there is a BUG ON that (correctly)
checks for preemptible to cover the call to rcu later on.
(Introduced with commit 8fa2206821
KVM: make guest mode entry to be rcu quiescent state)
This check might trigger depending on the kernel config.
Lets make sure that no preemption happens during kvm_guest_enter.
We can enable preemption again after the call to
rcu_virt_note_context_switch returns.
Please note that we continue to run s390 guests with interrupts
enabled.
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
CC: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Actually the Armada 370 DB (aka DB-88F6710-BP-DDR3) come with 1GB and
not 512MB.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull KVM bugfixes from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: use dynamic percpu allocations for shared msrs area
KVM: PPC: Book3S HV: Fix compilation without CONFIG_PPC_POWERNV
powerpc: Corrected include header path in kvm_para.h
Add rcu user eqs exception hooks for async page fault
Pull s390 patches from Martin Schwidefsky:
"Add the finit_module system call, fix the irq statistics in
/proc/stat, fix a s390dbf lockdep problem, a patch revert for a
problem that is not 100% understood yet, and a few patches to
fix warnings."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: define read*_relaxed functions
s390/topology: export cpu_topology
s390/pm: export pm_power_off
s390/pci: define isa_dma_bridge_buggy
s390/3215: partially revert tty close handling fix
s390/irq: count cpu restart events
s390/irq: remove split irq fields from /proc/stat
s390/irq: enable irq sum accounting for /proc/stat again
s390/syscalls: wire up finit_module syscall
s390/pci: remove dead code
s390/smp: fix section mismatch for smp_add_present_cpu()
s390/debug: Fix s390dbf lockdep problem in debug_(un)register_view()
This patch is brought to you by the letter 'H'.
Commit 20b279 breaks compatiblity with older perf binaries when run with
precise modifier (:p or :pp) by requiring the exclude_guest attribute to be
set. Older binaries default exclude_guest to 0 (ie., wanting guest-based
samples) unless host only profiling is requested (:H modifier). The workaround
for older binaries is to add H to the modifier list (e.g., -e cycles:ppH -
toggles exclude_guest to 1). This was deemed unacceptable by Linus:
https://lkml.org/lkml/2012/12/12/570
Between family in town and the fresh snow in Breckenridge there is no time left
to be working on the proper fix for this over the holidays. In the New Year I
have more pressing problems to resolve -- like some memory leaks in perf which
are proving to be elusive -- although the aforementioned snow is probably why
they are proving to be elusive. Either way I do not have any spare time to work
on this and from the time I have managed to spend on it the solution is more
difficult than just moving to a new exclude_guest flag (does not work) or
flipping the logic to include_guest (which is not as trivial as one would
think).
So, two options: silently force exclude_guest on as suggested by Gleb which
means no impact to older perf binaries or revert the original patch which
caused the breakage.
This patch does the latter -- reverts the original patch that introduced the
regression. The problem can be revisited in the future as time allows.
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Richter <robert.richter@amd.com>
Link: http://lkml.kernel.org/r/1356749767-17322-1-git-send-email-dsahern@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This is mostly a port of dbf62d5006 ("ARM: mm: introduce L_PTE_VALID
for page table entries") and 26ffd0d43b ("ARM: mm: introduce present,
faulting entries for PAGE_NONE") from ARM, which makes use of present,
faulting page table entries for page table entries mapped as PROT_NONE.
The main difference with this implementation is that we can make use of
the two pte type bits in order to avoid allocating a software bit for
identifying PROT_NONE pages, instead reserving the 10b suffix for these
types of mappings.
This is required to prevent users from accessing such pages via syscalls
such as read/write over a pipe.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Marking non-present ptes as read-only can corrupt file ptes, breaking
things like swap and file mappings.
This patch ensures that we only manipulate user pte bits when the pte
is marked present.
Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch is an arm64 version of ce73ec6db4 ("powerpc/vdso: Remove
redundant locking in update_vsyscall_tz()").
Timezone data is not protected, so the sequence counter is not required
to ensure consistency. Furthermore, having multiple paths updating the
counter leads to a race between update_vsyscall and update_vsyscall_tz,
so remove the timezone sequence counting from both the kernel and the
vdso.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Card detect for sdhci on Cubox is connected to the wrong pin
(sdio1_cd instead of sdio0_cd). With support for cd-gpios and
pinctrl add the corresponding properties to DT for Cubox.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Note that the pinctrl conversion also fixes GPIO support for ns2 boards.
Since commit f9e75922: "ARM: Kirkwood: Make use of mvebu pincltl and
gpio", the mvbu_gpio driver is used for DT boards. As mvbu_gpio relies
on the pinctrl driver, then a pinctrl definition must be given to allow
the GPIO configuration.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull ARM fixes from Russell King.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7616/1: cache-l2x0: aurora: Use writel_relaxed instead of writel
ARM: 7615/1: cache-l2x0: aurora: Invalidate during clean operation with WT enable
ARM: 7614/1: mm: fix wrong branch from Cortex-A9 to PJ4b
ARM: 7612/1: imx: Do not select some errata that depends on !ARCH_MULTIPLATFORM
ARM: 7611/1: VIC: fix bug in VIC irqdomain code
ARM: 7610/1: versatile: bump IRQ numbers
ARM: 7609/1: disable errata work-arounds which access secure registers
ARM: 7608/1: l2x0: Only set .set_debug on PL310 r3p0 and earlier
Retract back most macro definitions which went into the
user-visible mce.h header. Even though those bits are mostly
hardware-defined/-architectural, their naming is not. If we export them
to userspace, any kernel unification/renaming/cleanup cannot be done
anymore since those are effectively cast in stone. Besides, if userspace
wants those definitions, they can write their own defines and go crazy.
Signed-off-by: Borislav Petkov <bp@suse.de>
People are back from the holiday breaks, and it shows. Here are a bunch of
fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups,
a few __init annotation fixes and some error handling improvement
in their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to see
here, mostly from the OMAP PM changes, but nothing overly crazy.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9fE
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"People are back from the holiday breaks, and it shows. Here are a
bunch of fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups, a few
__init annotation fixes and some error handling improvement in
their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to
see here, mostly from the OMAP PM changes, but nothing overly crazy."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
pinctrl: mvebu: make pdma clock on dove mandatory
ARM: Dove: Add pinctrl clock to DT
dma: mv_xor: fix error handling for clocks
dma: mv_xor: fix error handling of mv_xor_channel_add()
arm: mvebu: Add missing ; for cpu node.
arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
arm: mvebu: Armada XP MV78230 has two cores, not one
clk: mvebu: Remove inappropriate __init tagging
ARM: Kirkwood: Use fixed-regulator instead of board gpio call
ARM: Kirkwood: Fix missing sdio clock
ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
...
on omap2 registers that causes issues trying to use common PM code.
Also fix few incorrect registers, and an issue for omap1 USB, and
few sparse fixes for issues that sneaked in with all the clean-up.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gqPM
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8-rc2/fixes-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
The biggest change is a fix to deal with different power state
on omap2 registers that causes issues trying to use common PM code.
Also fix few incorrect registers, and an issue for omap1 USB, and
few sparse fixes for issues that sneaked in with all the clean-up.
* tag 'omap-for-v3.8-rc2/fixes-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
ARM: OMAP1: fix USB configuration use-after-release
ARM: OMAP2/3: PRM: fix bogus OMAP2xxx powerstate return values
ARM: OMAP3: clock data: Add missing enable/disable for EMU clock
ARM: OMAP4: PRM: Correct wrong instance usage for reading reset sources
ARM: OMAP4: PRM: fix RSTTIME and RSTST offsets
ARM: OMAP4: PRM: Correct reset source map
ARM: OMAP: SRAM: resolve sparse warnings
ARM: OMAP AM33xx: hwmod data: resolve sparse warnings
ARM: OMAP: 32k counter: resolve sparse warnings
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
Most of them are EXYNOS5440 fixes which are for changing uart console,
cpu id (typo) and silent complaining gpio error in kernel boot.
* 'v3.8-samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: skip the clock initialization for exynos5440
ARM: EXYNOS: enable PINCTRL for EXYNOS5440
ARM: dts: use uart port1 for console on exynos4210-smdkv310
ARM: dts: use uart port0 for console on exynos5440-ssdk5440
ARM: SAMSUNG: fix the cpu id for EXYNOS5440
ARM: EXYNOS: Revise HDMI resource size
is unresponsive for quite a while. People start complaining the missing
of such an important fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ7DwYAAoJEFBXWFqHsHzOHnUH/2V7EKzq8g6FH5DyOf3+9x9f
I+KyjVusIFdbLIJZhswbTnd2f1k5FQnQ+djd6fERi/wZ8IcG70vPRscKIYrLX6po
gd0z684ORsBwNrHMfcKSY6DwZF2cLtP5BpyvtQzKHpP3nTYBgE7ePSFlfsAdJ5OG
C77/tj61B/bUe0Mm8ygjMCwYsdqaR2+MTdEcStvOmwd4x+PBT3uSd56TFhXW2kt5
Py2d48wowncNM5CVIW7vvH4kaaCW4h6mxnc3gyc8YS8h1JFItdYFSNUzT9Mb5ene
aM3He/pp82OoXm84Swhi5Ah5566WVor+bgnvJ1TmV4Q/yd6Cn+MA2nIOevTnJvo=
=Tjtj
-----END PGP SIGNATURE-----
Merge tag 'mxs-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
I have to send one critical mxsfb fix through arm-soc, as FB maintainer
is unresponsive for quite a while. People start complaining the missing
of such an important fix.
* tag 'mxs-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
video: mxsfb: fix crash when unblanking the display
ARM: dts: imx23-olinuxino: Fix IOMUX settings
when the port gets brought up. The other two are non-critical fixes,
which are sent together here, since it's still early -rc stage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJQ7Dk+AAoJEFBXWFqHsHzOUugIAJZblDy7ORFZhW0R8L4Be541
pS5aBGFY7VYCrL9BGUKGsLuITI+arbYFHc+H4nqhNMBAvgChPxJZMnaG4kp1Q5Vm
AVr9tNrwsauVHLlryUk4ekut4G4WWo1NDcFq4S6rxD/jxA/uP6rnMUCY6PX4LLL9
ZpGDb3BWQ2bbUaANu3cjc1I1/Gle1ir9LObm6ZC6l8MHTTG7hyTMHvS8eCZzmDbc
9z01ZrvTKn1AneeHOpArd2/jo14b6Kap8ykx2hdVUeBhIbZp3pomezZau9ya8/kB
+1BQVODdkOMzBm6gkIkfU3HbUPnIPL18MG/uKyD+f67YkX5YODinUVdq63upLxc=
=7yrS
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo:
It includes one critical fix - wrong flexcan2 clock will hang system
when the port gets brought up. The other two are non-critical fixes,
which are sent together here, since it's still early -rc stage.
* tag 'imx-fixes-3.8' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mx5: Fix MX53 flexcan2 clock
ARM: dts: imx31-bug: Fix manufacturer compatible string
clk: imx: Remove 'clock-output-names' from the examples
Use dynamic percpu allocations for the shared msrs structure,
to avoid using the limited reserved percpu space.
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The Armada XP GPIO controller has two ways of notifying interrupts:
using global interrupts or using per-CPU interrupts. In an attempt to
use the best available features, the 'marvell,armadaxp-gpio'
compatible string selects a variant of the gpio-mvebu driver that
makes use of the per-CPU interrupts.
Unfortunately, this doesn't work properly in a SMP context, because we
fall into cases where the GPIO interrupt is enabled on CPU X at the
GPIO controller level, but on CPU Y at the interrupt controller
level. It is not yet clear how to fix that easily.
So for 3.8, our approach is to switch to global interrupts for GPIOs,
so that we do not fall into this per-CPU interrupts problem.
This patch therefore fixes GPIO interrupts on Armada XP
platforms. Without this patch, GPIO interrupts simply do not work
reliably, because their proper operation depends on which CPU the code
requesting the interrupt is running.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch fixes some code that implements a work-around to a hardware bug in
the ac97 controller on the pxa27x. A bug in the controller's warm reset
functionality requires that the mfp used by the controller as the AC97_nRESET
line be temporarily reconfigured as a generic output gpio (AF0) and manually
held high for the duration of the warm reset cycle. This is what was done in
the original code, but it was broken long ago by commit fb1bf8cd
([ARM] pxa: introduce processor specific pxa27x_assert_ac97reset())
which changed the mfp to a GPIO input instead of a high output.
The fix requires the ac97 controller to obtain the gpio via gpio_request_one(),
with arguments that configure the gpio as an output initially driven high.
Tested on a palm treo 680 machine. Reportedly, this broken code only prevents a
warm reset on hardware that lacks a pull-up on the line, which appears to be the
case for me.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Just map the read*_relaxed() functions to their corresponding read*() functions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Export cpu_topology symbol, so it's available for modules.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Export pm_power_off symbol. Needed by at least one of the new device
drivers that come with CONFIG_PCI.
And all other architectures export that symbol as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Define isa_dma_bridge_buggy. Needed to make pci quirks compile:
drivers/pci/quirks.c: In function ‘quirk_isa_dma_hangs’:
drivers/pci/quirks.c:88:7: error: ‘isa_dma_bridge_buggy’ undeclared (first use in this function)
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Count CPU Restart events and make them visible via /proc/interrupts.
Every CPU hotplug (online) event will increase the per cpu counter.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Now that irq sum accounting for /proc/stat's "intr" line works again we
have the oddity that the sum field (first field) contains only the sum
of the second (external irqs) and third field (I/O interrupts).
The reason for that is that these two fields are already sums of all other
fields. So if we would sum up everything we would count every interrupt
twice.
This is broken since the split interrupt accounting was merged two years
ago: 052ff461c8 "[S390] irq: have detailed
statistics for interrupt types".
To fix this remove the split interrupt fields from /proc/stat's "intr"
line again and only have them in /proc/interrupts.
This restores the old behaviour, seems to be the only sane fix and mimics
a behaviour from other architectures where /proc/interrupts also contains
more than /proc/stat's "intr" line does.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For more than two years, since f2c66cd8ee
"/proc/stat: scalability of irq num per cpu" the output of /proc/stat is
broken.
The first field in the "intr" line should contain the sum of all interrupts,
however since the above mentioned change it is always zero.
The reason for that is that a per cpu irq sum variable had been introduced
which got incremented when calling kstat_incr_irqs_this_cpu(). However
on s390 we directly incremented only the per cpu per irq counter by accessing
the array element via kstat_cpu(smp_processor_id()).irqs[...].
So fix this and use the kstat_incr_irqs_this_cpu() wrapper which increments
both: the per cpu per irq counter and the per cpu irq sum counter.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Get rid of these:
arch/s390/pci/pci_dma.c:16:29: warning: ‘zpci_ioat_dt’ defined but not used [-Wunused-variable]
arch/s390/pci/pci.c:164:12: warning: ‘zpci_store_fib’ defined but not used [-Wunused-function]
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fixes this section mismatch:
WARNING: vmlinux.o(.text+0x145e4): Section mismatch in reference from the function
smp_add_present_cpu() to the function .cpuinit.text:register_cpu()
The function smp_add_present_cpu() references
the function __cpuinit register_cpu().
This is often because smp_add_present_cpu lacks a __cpuinit
annotation or the annotation of register_cpu is wrong.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The debug_register/unregister_view() functions call debugfs_remove()
while holding the debug_info spinlock. Because debugfs_remove() takes
a mutex and therefore can sleep this is not allowed. To fix the problem
we give up the debug_info lock before calling debugfs_remove().
The following shows the lockdep message:
[ INFO: possible circular locking dependency detected ]
-------------------------------------------------------
rmmod/4379 is trying to acquire lock:
(&sb->s_type->i_mutex_key#2){+.+.+.}, at: [<00000000003acae2>] debugfs_remove+0x5e/0xa
but task is already holding lock:
(&(&rc->lock)->rlock){-.-...}, at: [<000000000010a5ae>] debug_unregister_view+0x3a/0xd
which lock already depends on the new lock.
-> #0 (&sb->s_type->i_mutex_key#2){+.+.+.}:
[<00000000001b1644>] validate_chain+0x880/0x1154
[<00000000001b4d6c>] __lock_acquire+0x414/0xc44
[<00000000001b5c16>] lock_acquire+0xbe/0x178
[<0000000000614016>] mutex_lock_nested+0x66/0x36c
[<00000000003acae2>] debugfs_remove+0x5e/0xac
[<000000000010a620>] debug_unregister_view+0xac/0xd0
[<000003ff8002f140>] qeth_core_exit+0x48/0xf08 [qeth]
[<00000000001c35a4>] SyS_delete_module+0x1a4/0x260
[<0000000000618134>] sysc_noemu+0x22/0x28
[<000003fffd4704da>] 0x3fffd4704da
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
commit c045e3f13 (ARM: imx: include iram.h rather than mach/iram.h) changed the
location of iram.h, which causes the following build error when building the coda
driver:
drivers/media/platform/coda.c:27:23: error: mach/iram.h: No such file or directory
drivers/media/platform/coda.c: In function 'coda_probe':
drivers/media/platform/coda.c:2000: error: implicit declaration of function 'iram_alloc'
drivers/media/platform/coda.c:2001: warning: assignment makes pointer from integer without a cast
drivers/media/platform/coda.c: In function 'coda_remove':
drivers/media/platform/coda.c:2024: error: implicit declaration of function 'iram_free'
Since the content of iram.h is not imx specific, move it to
include/linux/platform_data/imx-iram.h instead. This is an intermediate solution
until the i.MX iram allocator is converted to the generic SRAM allocator.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- use correct uart driver for mvebu boards
- add a missing DT clocks
- gpio-poweroff level vs. edge triggering, use gpio_is_valid()
- remove an inappropriate __init, modules need to access function.
- various DT fixes
- error handling in mv_xor
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQ6vYDAAoJEAi3KVZQDZAeoHwIAKSw+8B601AixTZus7fp9wrE
M9Tk4VoCflDQ8uIh6sHrHQlwMi8NPVA6ogn6VoEYA7HnA/nGTx/Ij/XCpuPBdt8+
VM5gzonaKK16OswtLmUZIgJKDJt0Q+zw9K7u6UkWQW8IXyGlyK2gxYqJLQPHhebb
D3TyKdJqx7FBr2Oq3MJQshIN/TTSOA+q94oYUogc7qZpjsY8ZgnBbRWVBYEhRa+u
sS0vZ8LV5twOKqATJa4ZCXA4E3WoKOZKTgdXj4IRfRkeQh9WHmhH4aWwq7Kl72Ic
glBA6iCrA/6KvJx9H4AG5BK/Ltg2vfQDKo2XWMQtH8j2WwHfMqHMPS3qivjXg2s=
=jfqF
-----END PGP SIGNATURE-----
Merge tag 'mvebu_fixes_for_v3.8' of git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper:
fixes for mvebu/kirkwood v3.8
- use correct uart driver for mvebu boards
- add a missing DT clocks
- gpio-poweroff level vs. edge triggering, use gpio_is_valid()
- remove an inappropriate __init, modules need to access function.
- various DT fixes
- error handling in mv_xor
* tag 'mvebu_fixes_for_v3.8' of git://git.infradead.org/users/jcooper/linux:
pinctrl: mvebu: make pdma clock on dove mandatory
ARM: Dove: Add pinctrl clock to DT
dma: mv_xor: fix error handling for clocks
dma: mv_xor: fix error handling of mv_xor_channel_add()
arm: mvebu: Add missing ; for cpu node.
arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
arm: mvebu: Armada XP MV78230 has two cores, not one
clk: mvebu: Remove inappropriate __init tagging
ARM: Kirkwood: Use fixed-regulator instead of board gpio call
ARM: Kirkwood: Fix missing sdio clock
ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
Power: gpio-poweroff: Fix documentation and gpio_is_valid
ARM: Kirkwood: Fix missing clk for USB device.
arm: mvebu: Use dw-apb-uart instead of ns16650 as UART driver
Signed-off-by: Olof Johansson <olof@lixom.net>
I mismerged a previous branch from Alexander, and accidentally left
in ARCH_USES_GETTIMEOFFSET. Remove it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Alexander Shiyan <shc_work@mail.ru>
From Linus Walleij:
Two fixes to the Nomadik:
- Delete a dangling include
- Bump IRQ numbers to offset at 32
* tag 'nomadik-fixes-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: bump the IRQ numbers again
ARM: nomadik: delete dangling include
This fixes suspend to RAM adding necessary save and restore of L2 and GIC.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
When we fail to power down, we need to clear out the power request.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
With commit 384a290 (ARM: gic: use a private mapping for CPU target
interfaces), wake-up IPIs now go to all cores as the gic cpu interface
numbering may not follow core numbering. This broke secondary boot on
highbank since the boot address was already set for all secondary cores,
this caused all cores to boot before the kernel was ready.
Fix this by moving the setting of the jump address to
highbank_boot_secondary instead of highbank_smp_prepare_cpus and
highbank_cpu_die. Also, clear the address when we boot. This prevents
cores from booting before they are actually triggered and is also necessary
to get suspend/resume to work.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
With the addition of commit a0ae0240 (ARM: kernel: add device tree init
map function), the cpu reg values must match the cpu mpidr register or we'll
get warnings. For some reason, the CLUSTERID on highbank is 9, so the reg
value needs to be 0x90n to quiet the warnings.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
While device_type is considered deprecated, it is still needed for tools
like lshw to identify cpu nodes.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The second FlexCAN port uses different clock than the first one, configure
correct clock to prevent hanging of the system during bringing up of the port.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On 24-Nov-12, at 10:05 AM, John David Anglin wrote:
> In trying to build the debian libsigsegv2 package, I found that sigaltstack
> doesn't round ss.ss_sp. The tests intentionally pass an unaligned pointer.
> This results in the two stack overflow tests failing.
The attached patch fixes this issue.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Various GCC tests use gdb to simulate a multithreaded application. Many of
these tests have been failing on parisc linux.
GCC does this by using gdb to single-step the application, then gdb is used to
call other test specific code. Where this fails is when the application is
stepped into the delay slot of a taken branch. This sets the PSW B bit. When
the test specific code is executed, this usually clears the PSW B bit.
Currently, gdb is not allowed to set the B bit. So, the code falls through what
should be a taken branch.
The attached patch adds the PSW B bit to the set of bits that gdb is allowed to
set. In order to set the B bit, the trace system call must return using an
interrupt restore. The patch also modifies this code to use the saved IAOQ
values when they are saved by a ptrace syscall or interruption.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
The CPU irqs (timer and IPI) are not shared and only need to be claimed once.
A mismatch error occurs if they are claimed more than once.
Signed-off-by: John David Anglin <dave.anglin@nrc-cnrc.gc.ca>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Signed-off-by: Helge Deller <deller@gmx.de>
The attached change fixes a float conversion problem found running the
GCC testsuite with GCC configured with --with-arch=2.0.
The actual problem occurs for an exponent value of 63. This is the
maximum exponent value that can be passed. This causes a left shift by
32 in the else hunk of the macro. This causes undefined behavior and the
wrong value is returned for dresultB. The fix is the check "exponent <=
62". If the exponent is 63, dresultB is set to 0. The patch also
optimizes the operation a bit by copying "Sall(sgl_value) <<
SGL_EXP_LENGTH" to val, so that sgl_value is not modified.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
The IRQ array must be terminated by -1 and not by -1+OMAP_INTC_START
This led to having a resource list of 100s of IRQs.
Looks like this was caused by commit a2cfc509 (ARM: OMAP3+: hwmod: Add
AM33XX HWMOD data) that probably had some search and replace updates
done for the patch for sparse irq support.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated wit information about the breaking commit]
Signed-off-by: Tony Lindgren <tony@atomide.com>
During merge of the mvebu patches a clock gate for pinctrl was
lost. This patch just readds the clock gate.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Pull MIPS fixes from Ralf Baechle:
"Various fixes across the tree. The modpost error due to
virt_addr_valid() not being usable from modules required a number of
preparatory cleanups so a clean fix was possible."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: 64-bit: Fix build if !CONFIG_MODULES
MIPS: Wire up finit_module syscall.
MIPS: Fix modpost error in modules attepting to use virt_addr_valid().
MIPS: page.h: Remove now unnecessary #ifndef __ASSEMBLY__ wrapper.
MIPS: Switch remaining assembler PAGE_SIZE users to <asm/asm-offsets.h>.
MIPS: Include PAGE_S{IZE,HIFT} in <asm/offset.h>.
MIPS: Don't include <asm/page.h> unnecessarily.
MIPS: Fix comment.
Revert "MIPS: Optimise TLB handlers for MIPS32/64 R2 cores."
MIPS: perf: Fix build failure in XLP perf support.
MIPS: Alchemy: Make 32kHz and r4k timer coexist peacefully
Pull microblaze update from Michal Simek:
"This fixes noMMU kernel and I have also added defconfig updates which
fix issue with one external dependency and enable all xilinx device
drivers for 0-day testing system.
Additionally wire up finit_module system call, and do highmem fixup
and pci warnings reported by the 0-day testing system"
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Update microblaze defconfigs
microblaze: Fix pci compilation and sparse warnings
microblaze: Add finit_module syscall
microblaze: Kill __kmap_atomic()
microblaze: Change section flags for noMMU
microblaze: Microblaze wants sys_fork for noMMU too
The use of writel instead of writel_relaxed lead to deadlock in some
situation (SMP on Armada 370 for instance). The use of writel_relaxed
as it was done in the rest of this driver fixes this bug.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a bug for Aurora L2 cache controller when the
write-through mode is enable. For the clean operation even if we don't
have to flush the lines we still need to invalidate them.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Compiling 3.8-rc1 fails for some m68k targets (the non-mmu ones) with:
CC arch/m68k/mm/init.o
arch/m68k/mm/init.c: In function ‘mem_init’:
arch/m68k/mm/init.c:191:2: error: implicit declaration of function ‘init_pointer_table’
arch/m68k/mm/init.c:191:36: error: ‘kernel_pg_dir’ undeclared (first use in this function)
arch/m68k/mm/init.c:191:36: note: each undeclared identifier is reported only once for each function it appears in
arch/m68k/mm/init.c:192:18: error: ‘PTRS_PER_PGD’ undeclared (first use in this function)
arch/m68k/mm/init.c:194:4: error: implicit declaration of function ‘__pgd_page’
arch/m68k/mm/init.c:198:6: error: ‘zero_pgtable’ undeclared (first use in this function)
make[2]: *** [arch/m68k/mm/init.o] Error 1
make[1]: *** [arch/m68k/mm] Error 2
make[1]: Leaving directory `/home/gerg/new-wave.git/linux-3.x'
make: *** [linux] Error 1
Change the conditions that define init_pointer_table so that it matches what
actually uses it.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
To be consistent with the set of MMU definitions we should define KMAP_START
and KMAP_END. Future common m68k code will use their values.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
If CONFIG_ARCH_MULTIPLATFORM & CONFIG_ARCH_MVEBU are both enabled,
__v7_pj4b_setup is added between __v7_ca9mp_setup and __v7_setup.
But there's no jump instruction added. If the chip is Cortex A5/A9,
it goes through __v7_pj4b_setup also. It results in system hang.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit 62e4d357a (ARM: 7609/1: disable errata work-arounds which access
secure registers) ARM_ERRATA_743622/751472 depends on !ARCH_MULTIPLATFORM.
Since imx has been converted to multiplatform, the following warning happens:
$ make imx_v6_v7_defconfig
warning: (SOC_IMX6Q && ARCH_TEGRA_2x_SOC && ARCH_TEGRA_3x_SOC) selects
ARM_ERRATA_751472 which has unmet direct dependencies (CPU_V7 &&
!ARCH_MULTIPLATFORM)
warning: (SOC_IMX6Q && ARCH_TEGRA_3x_SOC) selects ARM_ERRATA_743622
which has unmet direct dependencies (CPU_V7 && !ARCH_MULTIPLATFORM)
warning: (SOC_IMX6Q && ARCH_TEGRA_3x_SOC) selects ARM_ERRATA_743622
which has unmet direct dependencies (CPU_V7 && !ARCH_MULTIPLATFORM)
warning: (SOC_IMX6Q && ARCH_TEGRA_2x_SOC && ARCH_TEGRA_3x_SOC) selects
ARM_ERRATA_751472 which has unmet direct dependencies (CPU_V7 &&
!ARCH_MULTIPLATFORM)
Recommended approach is to remove ARM_ERRATA_743622/751472 from being selected
by SOC_IMX6Q and apply such workarounds into the bootloader.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Armada XP MV78230 DT include file is missing a ; at the
end of the cpu node.
Reported-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
We originally thought that the MV78230 variant of the Armada XP had
four Ethernet interfaces, like the other variants MV78260 and
MV78460. In fact, this is not true, and the MV78230 has only three
Ethernet interfaces.
So, the definitions of the Ethernet interfaces is now done as follows:
* armada-370-xp.dtsi: definitions of the first two interfaces, that
are common to Armada 370 and Armada XP
* armada-xp.dtsi: definition of the third interface, common to all
Armada XP variants.
* armada-xp-mv78260.dtsi and armada-xp-mv78460.dtsi: definition of
the fourth interface.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Contrary to our understanding at the time armada-xp-mv78230.dtsi was
written, the MV78230 variant of the Armada XP SoC has two cores and
not one. This patch updates the .dtsi file to take into account this
reality.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
With the change to a DT based pinctrl/gpio driver, using gpio API
calls in board-*.c files no longer works, a dereferenced NULL pointer
exception occurs instead. By converting the GPIO code into a
fixed-regulator which gets probed later once pinctrl/gpio is
available, we avoid the exception.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mplch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
We moved to declaring clk gates in DT. However, device which do not
yet have a DT binding need to have a clkdev alias. This was missing
for SDIO.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mplch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Clock Management of kirkwood has moved to DT clock providers.
However, TWSI1 has not yet been done.
This switches TWSI1 of 88f6282 to DT clock providers.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Without the clock being held by a driver, it gets turned off at a bad
time causing the SoC to lockup. This is often during reboot.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The UART controller used in the Armada 370 and Armada XP SoCs is the
Synopsys DesignWare 8250 (aka Synopsys DesignWare ABP UART). The
improper use of the ns16550 can lead to a kernel oops during boot if
a character is sent to the UART before the initialization of the
driver. The DW APB has an extra interrupt that gets raised when
writing to the LCR when busy. This explains why we need to use
dw-apb-uart driver to handle this.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Fixes this build breakage:
arch/powerpc/kvm/book3s_hv_ras.c: In function ‘kvmppc_realmode_mc_power7’:
arch/powerpc/kvm/book3s_hv_ras.c:126:23: error: ‘struct paca_struct’ has no member named ‘opal_mc_evt’
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Since exynos5440 can support only common clk stuff, so this
patch skips legacy exynos5 clock initialization.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The main reason is 0-day testing system which can directly
use these defconfigs for testing.
Enable support for all xilinx drivers which Microblaze
can use and disable dependency on external rootfs.cpio.
There is only one exception which is axi ethernet driver
which still uses NO_IRQ which is not defined for Microblaze.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Warning log:
CHECK arch/microblaze/pci/pci-common.c
arch/microblaze/pci/pci-common.c:290:14: warning: Using plain integer as NULL pointer
arch/microblaze/pci/pci-common.c:1127:6: warning: symbol
'pcibios_allocate_bus_resources' was not declared. Should it be static?
arch/microblaze/pci/pci-common.c:1436:61: warning: incorrect type in argument 3 (different base types)
arch/microblaze/pci/pci-common.c:1436:61: expected unsigned int [unsigned] [usertype] offset
arch/microblaze/pci/pci-common.c:1436:61: got void [noderef] <asn:2>*
CC arch/microblaze/pci/pci-common.o
arch/microblaze/pci/pci-common.c: In function 'pci_proc_domain':
arch/microblaze/pci/pci-common.c:825:25: warning: unused variable 'hose' [-Wunused-variable]
arch/microblaze/pci/pci-common.c: In function 'pcibios_allocate_bus_resources':
arch/microblaze/pci/pci-common.c:1182:1: warning: label 'clear_resource' defined but not used [-Wunused-label]
arch/microblaze/pci/pci-common.c: In function 'pcibios_setup_phb_resources':
arch/microblaze/pci/pci-common.c:1436:2: warning: passing argument 3 of
'pci_add_resource_offset' makes integer from pointer without a cast [enabled by default]
include/linux/pci.h:999:6: note: expected 'resource_size_t' but argument is of type 'void *'
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In the compatible field we should point the manufacturer of the board, which
in this case is Buglabs.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Here are the remaining __dev* removal patches against the 3.8-rc2 tree.
All of these patches were previously sent to the subsystem maintainers,
most of them were picked up and pushed to you, but there were a number
that fell through the cracks, and new drivers were added during the
merge window, so this series cleans up the rest of the instances of
these markings.
Third time's the charm...
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDmHOIACgkQMUfUDdst+ykTZgCePgK84Im3FFooEXJwaPbaf4ls
lO4AoMEDoWK+BHWOsjQwFPOwFFPEN2Xh
=6oAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core __dev* removal patches - take 3 - from Greg Kroah-Hartman:
"Here are the remaining __dev* removal patches against the 3.8-rc2
tree. All of these patches were previously sent to the subsystem
maintainers, most of them were picked up and pushed to you, but there
were a number that fell through the cracks, and new drivers were added
during the merge window, so this series cleans up the rest of the
instances of these markings.
Third time's the charm...
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflict with the pinctrl pull in pinctrl-sirf.c.
* tag 'driver-core-3.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (54 commits)
misc: remove __dev* attributes.
include: remove __dev* attributes.
Documentation: remove __dev* attributes.
Drivers: misc: remove __dev* attributes.
Drivers: block: remove __dev* attributes.
Drivers: bcma: remove __dev* attributes.
Drivers: char: remove __dev* attributes.
Drivers: clocksource: remove __dev* attributes.
Drivers: ssb: remove __dev* attributes.
Drivers: dma: remove __dev* attributes.
Drivers: gpu: remove __dev* attributes.
Drivers: infinband: remove __dev* attributes.
Drivers: memory: remove __dev* attributes.
Drivers: mmc: remove __dev* attributes.
Drivers: iommu: remove __dev* attributes.
Drivers: power: remove __dev* attributes.
Drivers: message: remove __dev* attributes.
Drivers: macintosh: remove __dev* attributes.
Drivers: mfd: remove __dev* attributes.
pstore: remove __dev* attributes.
...
This fixes up all of the smaller arches that had __dev* markings for
their platform-specific drivers.
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Bob Liu <lliubbo@gmail.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Myron Stowe <myron.stowe@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Yong Zhang <yong.zhang0@gmail.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Jan Glauber <jang@linux.vnet.ibm.com>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitconst,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Daniel Drake <dsd@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bump the IRQ numbers from offset at 1 (right above NO_IRQ)
to 32. This is the painful way to learn that if you're using
SPARSE_IRQ and avoid to define .nr_irqs in your machine,
the first 16 IRQs will be pre-allocated, and the IRQdomain
code (as the VIC core code before it) will then assume
that all IRQ descriptors are pre-allocated, and 16 of them
are - by somebody else. So mapping the IRQs will fail in
irq_create_mapping(). Moving the offset upward rids us of
this problem.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reference to the old include header for the FSMC NAND
MTD driver was somehow left in place, get rid of it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- i.MX5 register configuration
- Swap a kfree to devm_kfree() to avoid memory
corruption in the at91 driver
- Add the missing device tree binding doc for the
SIRF pin controller
- Enable the SIRF GPIO pull up/down configuration
from the device tree, it was previously retired
from the hard-coded approach.
- NULL check for the prcm_base in the Nomadik pin
controller.
- Provide the prcm_base from the device tree in the
DT boot path for the Nomadik pin controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=ca6M
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"A first round of pinctrl fixes for v3.8:
- i.MX5 register configuration
- Swap a kfree to devm_kfree() to avoid memory corruption in the at91
driver
- Add the missing device tree binding doc for the SIRF pin controller
- Enable the SIRF GPIO pull up/down configuration from the device
tree, it was previously retired from the hard-coded approach.
- NULL check for the prcm_base in the Nomadik pin controller.
- Provide the prcm_base from the device tree in the DT boot path for
the Nomadik pin controller."
* tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
ARM: ux500: add pinctrl address resources
pinctrl: nomadik: return if prcm_base is NULL
pinctrl: sirf: enable GPIO pullup/down configuration from dts
pinctrl: sirf: add missing DT-binding document
pinctrl: fix comment mistake
drivers/pinctrl/pinctrl-at91.c: convert kfree to devm_kfree
pinctrl: imx5: fix GPIO_8 pad CAN1_RXCAN configuration
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a couple of small powerpc fixes. They aren't new bugs (and
they are both CCed to stable) but I didn't see the point of sitting on
the fixes any longer."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Add missing NULL terminator to avoid boot panic on PPC40x
powerpc/vdso: Remove redundant locking in update_vsyscall_tz()
logs are available here:
http://www.pwsan.com/omap/testlogs/prcm_fixes_b_3.8-rc/20130102120724/
The 3730 Beagle XM here has an intermittent failure mounting SD root,
but the suspicion right now is that this is due to a failing SD card,
rather than any change introduced by these patches.
This second version includes a few changes requested by Tony Lindgren.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQ5IkPAAoJEMePsQ0LvSpL/RQQAJUbGPZTdMEH2DHHDVPRxgBE
bWEg0RQfzheOLfFvfot2tReJoN7GMlhzcDq2DSHZLwp5b9XgOgOJdNdldvrvFljD
p3QEy+y/7ZSgsAdgDV33vAAUAv4c0CIh0cKgw3JwOn/dqVSbiMXXqXe1kZe419gi
bbJHBr6fZH63qvGzkjI17vl3lDq6RsX7vgtEQ9TeiTMUAOnrXzp3rt9oDNVsChSs
Ml6h1WKnxQdMFjbNNmBOUGltSg7O1rwuWeS/9mg77yV3lIZ5QdmAVlcq6lUB+jqy
CWhAYbrhXMBPYFaxzw0I8h00m0VNBSOZf2e1d5Lw8wU8dVxQ3PVZCI4SyRssBdd3
T+91zy4Axmo+SWrkTxpq+yE2Sn1AMZC4mJwI62UhCZV8TPPvek8IlK3ktKeV97ql
BNehuGYqbc3u5TiIjO8K+akTBKKTVDdXaah9ms8rtQ4hcwLwC0VA/71R9qaQJx3E
mGf3pRK6FSV83vEMrGb2mRk3ByGHzpYlMD0sb4+0OFvkj5Hyv7OCPb0TJapn6OPO
vpeG6pIbHN3p/mKrj/RNHVtvpV5/mHJmMOXgkcXLcdlZhsnGE21dqw/vPrvjf3Wa
SnUp7q48/4a2FP2d0KpQ+CpHyLyNEs4x4zs9hfjHGsYs1fWBwdu0+/8rVPaAEjjB
iUa8sxlv/1o0rJfiyRkd
=oUTN
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-a2-for-v3.8-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.8-rc2/fixes
Some OMAP PRCM and sparse fixes against v3.8-rc1. A basic set of test
logs are available here:
http://www.pwsan.com/omap/testlogs/prcm_fixes_b_3.8-rc/20130102120724/
The 3730 Beagle XM here has an intermittent failure mounting SD root,
but the suspicion right now is that this is due to a failing SD card,
rather than any change introduced by these patches.
This second version includes a few changes requested by Tony Lindgren.
Linux was granted a new system call to load modules by file descriptor
in commit 34e1169d99 ("module: add syscall to load module from fd").
Wire it up for ia64 (ready for the Chrome port :-)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All files which uses user unified macros from uaccess.h
(get_user/put_user/clear_user/copy_tofrom_user/
strnlen_user and strncpy_user) generate this
warning messages:
Assembler messages:
Warning: ignoring changed section attributes for .discard
Setting up discard executable section flang for __EX_TABLE_SECTION
macro removed all these warnings.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch "generic sys_fork / sys_vfork / sys_clone"
(sha1: d2125043ae)
introduced generic sys_fork with implementation for noMMU
which returns EINVAL for noMMU.
and the patch "microblaze: switch to generic fork/vfork/clone"
(sha1: f3268edbe6)
enable sys_fork only for MMU which is causing compilation
failure on noMMU system.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The locking in update_vsyscall_tz() is not only unnecessary because the vdso
code copies the data unproteced in __kernel_gettimeofday() but also
introduces a hard to reproduce race condition between update_vsyscall()
and update_vsyscall_tz(), which causes user space process to loop
forever in vdso code.
The following patch removes the locking from update_vsyscall_tz().
Locking is not only unnecessary because the vdso code copies the data
unprotected in __kernel_gettimeofday() but also erroneous because updating
the tb_update_count is not atomic and introduces a hard to reproduce race
condition between update_vsyscall() and update_vsyscall_tz(), which further
causes user space process to loop forever in vdso code.
The below scenario describes the race condition,
x==0 Boot CPU other CPU
proc_P: x==0
timer interrupt
update_vsyscall
x==1 x++;sync settimeofday
update_vsyscall_tz
x==2 x++;sync
x==3 sync;x++
sync;x++
proc_P: x==3 (loops until x becomes even)
Because the ++ operator would be implemented as three instructions and not
atomic on powerpc.
A similar change was made for x86 in commit 6c260d5863
("x86: vdso: Remove bogus locking in update_vsyscall_tz")
Signed-off-by: Shan Hai <shan.hai@windriver.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull watchdog fixes from Wim Van Sebroeck:
"This fixes some small errors in the new da9055 driver, eliminates a
compiler warning and adds DT support for the twl4030_wdt driver (so
that we can have multiple watchdogs with DT on the omap platforms)."
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: twl4030_wdt: add DT support
watchdog: omap_wdt: eliminate unused variable and a compiler warning
watchdog: da9055: Don't update wdt_dev->timeout in da9055_wdt_set_timeout error path
watchdog: da9055: Fix invalid free of devm_ allocated data
PCI: Reduce Ricoh 0xe822 SD card reader base clock frequency to 50MHz
PCI: Remove spurious error for sriov_numvfs store and simplify flow
PCI: Add PCIe Link Capability link speed and width names
PCI/PM: Do not suspend port if any subordinate device needs PME polling
PCI: Work around Stratus ftServer broken PCIe hierarchy (fix DMI check)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=Ehs+
-----END PGP SIGNATURE-----
Merge tag '3.8-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Some fixes for v3.8. They include a fix for the new SR-IOV sysfs
management support, an expanded quirk for Ricoh SD card readers, a
Stratus DMI quirk fix, and a PME polling fix."
* tag '3.8-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Reduce Ricoh 0xe822 SD card reader base clock frequency to 50MHz
PCI/PM: Do not suspend port if any subordinate device needs PME polling
PCI: Add PCIe Link Capability link speed and width names
PCI: Work around Stratus ftServer broken PCIe hierarchy (fix DMI check)
PCI: Remove spurious error for sriov_numvfs store and simplify flow
Fix build failure if building a monolithic kernel due to
arch/mips/kernel/Kconfig selecting MODULES_USE_ELF_REL[A] without checking
to see if MODULES is set or not. This leads to 'struct module' not
existing, which triggers a compile failure in arch/mips/kernel/module-rela.c
when the compiler attempts to dereference me->name:
CC arch/mips/kernel/module-rela.o
arch/mips/kernel/module-rela.c: In function ‘apply_r_mips_26_rela’:
arch/mips/kernel/module-rela.c:38:74: error: dereferencing pointer to incomplete type
arch/mips/kernel/module-rela.c:46:12: error: dereferencing pointer to incomplete type
arch/mips/kernel/module-rela.c: In function ‘apply_relocate_add’:
arch/mips/kernel/module-rela.c:133:13: error: dereferencing pointer to incomplete type
make[2]: *** [arch/mips/kernel/module-rela.o] Error 1
Signed-off-by: Joshua Kinard <kumba@gentoo.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4749/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On OMAP2xxx chips, the register bitfields for the
PM_PWSTCTRL_*.POWERSTATE and PM_PWSTST_*.LASTSTATEENTERED are
different than those used on OMAP3/4. The order is reversed. So, for
example, on OMAP2xxx, 0x0 indicates 'ON'; but on OMAP3/4, 0x0
indicates 'OFF'. Similarly, on OMAP2xxx, 0x3 indicates 'OFF', but on
OMAP3/4, 0x3 indicates 'ON'.
To fix this, we treat the OMAP3/4 values as the powerdomain API
values, and create new low-level powerdomain functions for the
OMAP2xxx chips which translate between the OMAP2xxx values and the
OMAP3/4 values.
Without this patch, the conversion of the OMAP2xxx PM code to the
functional powerstate code results in a non-booting kernel.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The ETM/ETB drivers for OMAP3, enable the emu_src_ck clock in order
to access the ETM/ETB hardware. The emu_src_ck should enable the EMU
clock domain so that the ETM/ETB hardware is accessible. However,
currently when enabling the emu_src_ck the EMU clock domain is not
being enabled and so the ETM/ETB drivers are failing. Add enable/disable
clock functions to enable the EMU clock domain when enabling the
emu_src_ck.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
To read reset sources registers we have to use PRM_DEVICE_INST
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
RSTTIME is offset 0x8 and RSTST is offset 0x04 for OMAP4430 and
OMAP4460.
Signed-off-by: Nishanth Menon <nm@ti.com>
[ivan.khoronzhuk@ti.com: ported from k3.4]
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In the map for reset sources register we use defines intended for
using with PRM_RSTCTRL register. So fix it.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 9b064fc3f9 (new helper:
compat_user_stack_pointer()) introduces a call to current_pt_regs()
which is defined in linux/ptrace.h, not currently included asm/compat.h.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add DT support for twl4030_wdt. This is needed to get twl4030_wdt to
probe when booting with DT.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The VIC irqdomain code added in commit
07c9249f1f
"ARM: 7554/1: VIC: use irq_domain_add_simple()"
Had two bugs:
1) It didn't call irq_create_mapping() once on each
valid irq source in the slowpath when registering
the controller.
2) It passed a -1 as IRQ offset for the DT case, whereas
0 should be passed as invalid IRQ instead.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Versatile starts to register Linux IRQ numbers from offset 0
which is illegal, since this is NO_IRQ. Bump all hard-coded IRQs
by 32 to get rid of the problem.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In order to support secure and non-secure platforms in multi-platform
kernels, errata work-arounds that access secure only registers need to
be disabled. Make all the errata options that fit in this category
depend on !CONFIG_ARCH_MULTIPLATFORM.
This will effectively remove the errata options as platforms are
converted over to multi-platform.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PL310 errata work-arounds using .set_debug function are only needed on
r3p0 and earlier, so check the rev and only set .set_debug on older revs.
Avoiding debug register accesses fixes aborts on non-secure platforms
like highbank. It is assumed that non-secure platforms needing these
work-arounds have already implemented .set_debug with secure monitor
calls.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit bb77209432 ("ARM: OMAP: Move
omap2+ specific parts of sram.c to mach-omap2") adds some new sparse
warnings:
arch/arm/plat-omap/sram.c:43:6: warning: symbol 'omap_sram_push_address' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:65:6: warning: symbol 'omap_sram_reset' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:73:13: warning: symbol 'omap_map_sram' was not declared. Should it be static?
This second version fixes the warnings by including <plat/sram.h>, at
Tony's request.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Commit 70384a6af0 ("ARM: OMAP3+:
hwmod: Add AM33XX HWMOD data for davinci_mdio module") adds two
new sparse warnings:
arch/arm/mach-omap2/omap_hwmod_33xx_data.c:2518:30: warning: symbol 'am33xx_mdio_addr_space' was not declared. Should it be static?
arch/arm/mach-omap2/omap_hwmod_33xx_data.c:2526:26: warning: symbol 'am33xx_cpgmac0__mdio' was not declared. Should it be static?
Fix by marking the two new records as static.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
From Tony Lindgren:
Here are few more patches to finish the omap changes for
multiplatform conversion that are not strictly fixes, but
were too complex to do with the dependencies during the
merge window. Those are to move of serial-omap.h to
platform_data, and the removal of remaining cpu_is_omap
macro usage outside mach-omap2.
Then there are several trivial fixes for typos and few
minimal omap2plus_defconfig updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RE6Z
-----END PGP SIGNATURE-----
Merge tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM cleanups for omap from Olof Johansson:
"From Tony Lindgren:
Here are few more patches to finish the omap changes for multiplatform
conversion that are not strictly fixes, but were too complex to do
with the dependencies during the merge window. Those are to move of
serial-omap.h to platform_data, and the removal of remaining
cpu_is_omap macro usage outside mach-omap2.
Then there are several trivial fixes for typos and few minimal
omap2plus_defconfig updates."
* tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arch/arm/mach-omap2/dpll3xxx.c: drop if around WARN_ON
OMAP2: Fix a typo - replace regist with register.
ARM/omap: use module_platform_driver macro
ARM: OMAP2+: PMU: Remove unused header
ARM: OMAP4: remove duplicated include from omap_hwmod_44xx_data.c
ARM: OMAP2+: omap2plus_defconfig: enable twl4030 SoC audio
ARM: OMAP2+: omap2plus_defconfig: Add tps65217 support
ARM: OMAP2+: enable devtmpfs and devtmpfs automount
ARM: OMAP2+: omap_twl: Change TWL4030_MODULE_PM_RECEIVER to TWL_MODULE_PM_RECEIVER
ARM: OMAP2+: Drop plat/cpu.h for omap2plus
ARM: OMAP: Split fb.c to remove last remaining cpu_is_omap usage
MAINTAINERS: Add an entry for omap related .dts files
This patch removes following warning in kernel boot log,
Because EXYNOS5440 can support only Pinctrl not GPIO.
WARNING: at drivers/gpio/gpio-samsung.c:3102 samsung_gpiolib_init+0x68/0x8c()
Unknown SoC in gpio-samsung, no GPIOs added
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ERROR: "min_low_pfn" [drivers/block/aoe/aoe.ko] undefined!
Fixed by moving the implementation of virt_addr_valid() into the kernel
proper and exporting it which removes the pains of an inline or macro
implementation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
So far we're jumping through hoops to keep the file usable from assembler
source but it's getting just too painful. Turns out that many uses of
<asm/page.h> are unnecessary anyway, so just remove those.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 1fe97c8f6a ("ARM: OMAP: Make OMAP
clocksource source selection using kernel param") results in a new warning
from sparse:
arch/arm/plat-omap/counter_32k.c:86:12: warning: symbol 'omap_init_clocksource_32k' was not declared. Should it be static?
This second version fixes this warning by including <plat/counter-32k.h>,
at Tony's request.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Reduce the HDMI resource size from 0x100000 to 0x70000 so it
doesn't overlap the Displayport resource space.
HDMI: (0x14530000 - 0x145A0000)
DP: (0x145B0000 - 0x145B1000)
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Commit 4be3d2f396 ("MIPS: perf: Add XLP
support for hardware perf.") added UNSUPPORTED_PERF_EVENT_ID which was
removed a while back.
Cc: Zi Shen Lim <zlim@netlogicmicro.com>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: Zi Shen Lim <zlim@netlogicmicro.com>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Acked-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: https://patchwork.linux-mips.org/patch/4730/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that the r4k timer is registered no matter what, bump the rating of
the Alchemy 32kHz timer so that it gets used when it is working,
and fall back on the r4k when it isn't.
This fixes a timer-related hang on platform with a working 32kHz timer
(the better rated c0 timer stops while executing 'wait' leading to (almost)
eternal sleep) and an oops on boot on platforms without a working 32kHz
timer (due to double registration of the r4k timer).
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/4728/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 284f5f9 was intended to disable the "only_one_child()" optimization
on Stratus ftServer systems, but its DMI check is wrong. It looks for
DMI_SYS_VENDOR that contains "ftServer", when it should look for
DMI_SYS_VENDOR containing "Stratus" and DMI_PRODUCT_NAME containing
"ftServer".
Tested on Stratus ftServer 6400.
Reported-by: Fadeeva Marina <astarta@rat.ru>
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=51331
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.5+
Current nmk_pinctrl driver is not PRCMU dependent anymore, so it needs
its own DT address resources to work properly, as done for
platform_device in:
f482833 ARM: ux500: add PRCM register base for pinctrl
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 0049fb2603 ("OMAPFB: use
dma_alloc_attrs to allocate memory") we have one non-arch user of
dma_{alloc,free}_attrs().
Hence provide these functions, as wrappers around
dma_{alloc,free}_coherent().
Note that most architectures do it the other way around. But as so far
m68k doesn't support the attributes at all, our solution should generate
smaller code.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
On the imx23-olinuxino board GPIO2_1 is connected to the LED and GPIO0_17
is the USB PHY reset.
So make the IOMUX assignment properly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Commit 68136b10 ("ARM: sunxi: Change device tree naming scheme for
sunxi") changed the naming scheme and the compatible strings used in the
device trees related to the sunXi platform, but forgot to change the
compatible string in the DT machine definition.
This prevents the kernel from booting on these boards.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* a set of patches from Lars-Peter Clausen to generalize asm/mmu.h
and use it in the architectures that don't need any special handling.
* A patch from Will Deacon to remove the {read,write}s{b,w,l} as
discussed during the arm64 review
* A patch from James Hogan that helps with the meta architecture
series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=uewR
-----END PGP SIGNATURE-----
Merge tag 'asm-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanup from Arnd Bergmann:
"These are a few cleanups for asm-generic:
- a set of patches from Lars-Peter Clausen to generalize asm/mmu.h
and use it in the architectures that don't need any special
handling.
- A patch from Will Deacon to remove the {read,write}s{b,w,l} as
discussed during the arm64 review
- A patch from James Hogan that helps with the meta architecture
series."
* tag 'asm-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
xtensa: Use generic asm/mmu.h for nommu
h8300: Use generic asm/mmu.h
c6x: Use generic asm/mmu.h
asm-generic/mmu.h: Add support for FDPIC
asm-generic/mmu.h: Remove unused vmlist field from mm_context_t
asm-generic: io: remove {read,write} string functions
asm-generic/io.h: remove asm/cacheflush.h include
Commit db5b0ae007 ("Merge tag 'dt' of git://git.kernel.org/.../arm-soc")
causes a duplicated build target. This patch fixes it and sorts out the
build target alphabetically so that we can recognize something wrong
easily.
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull VFS update from Al Viro:
"fscache fixes, ESTALE patchset, vmtruncate removal series, assorted
misc stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (79 commits)
vfs: make lremovexattr retry once on ESTALE error
vfs: make removexattr retry once on ESTALE
vfs: make llistxattr retry once on ESTALE error
vfs: make listxattr retry once on ESTALE error
vfs: make lgetxattr retry once on ESTALE
vfs: make getxattr retry once on an ESTALE error
vfs: allow lsetxattr() to retry once on ESTALE errors
vfs: allow setxattr to retry once on ESTALE errors
vfs: allow utimensat() calls to retry once on an ESTALE error
vfs: fix user_statfs to retry once on ESTALE errors
vfs: make fchownat retry once on ESTALE errors
vfs: make fchmodat retry once on ESTALE errors
vfs: have chroot retry once on ESTALE error
vfs: have chdir retry lookup and call once on ESTALE error
vfs: have faccessat retry once on an ESTALE error
vfs: have do_sys_truncate retry once on an ESTALE error
vfs: fix renameat to retry on ESTALE errors
vfs: make do_unlinkat retry once on ESTALE errors
vfs: make do_rmdir retry once on ESTALE errors
vfs: add a flags argument to user_path_parent
...
Pull signal handling cleanups from Al Viro:
"sigaltstack infrastructure + conversion for x86, alpha and um,
COMPAT_SYSCALL_DEFINE infrastructure.
Note that there are several conflicts between "unify
SS_ONSTACK/SS_DISABLE definitions" and UAPI patches in mainline;
resolution is trivial - just remove definitions of SS_ONSTACK and
SS_DISABLED from arch/*/uapi/asm/signal.h; they are all identical and
include/uapi/linux/signal.h contains the unified variant."
Fixed up conflicts as per Al.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
alpha: switch to generic sigaltstack
new helpers: __save_altstack/__compat_save_altstack, switch x86 and um to those
generic compat_sys_sigaltstack()
introduce generic sys_sigaltstack(), switch x86 and um to it
new helper: compat_user_stack_pointer()
new helper: restore_altstack()
unify SS_ONSTACK/SS_DISABLE definitions
new helper: current_user_stack_pointer()
missing user_stack_pointer() instances
Bury the conditionals from kernel_thread/kernel_execve series
COMPAT_SYSCALL_DEFINE: infrastructure
Pull ARM fixes from Russell King:
"A number of smallish fixes scattered around the ARM code. Probably
the most serious one is the one from Al addressing the missing locking
in the swap emulation code."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7607/1: realview: fix private peripheral memory base for EB rev. B boards
ARM: 7606/1: cache: flush to LoUU instead of LoUIS on uniprocessor CPUs
ARM: missing ->mmap_sem around find_vma() in swp_emulate.c
ARM: 7605/1: vmlinux.lds: Move .notes section next to the rodata
ARM: 7602/1: Pass real "__machine_arch_type" variable to setup_machine_tags() procedure
ARM: 7600/1: include CONFIG_DEBUG_LL_INCLUDE rather than mach/debug-macro.S
Here are a few more fixes for 3.8. Two branches of fixes for Samsung
platforms, including fixes for the audio build errors on all non-DT
platforms. There's also a fixup to the sunxi device-tree file renames
due to a bad patch application by me, and a fix for OMAP due to function
renames merged through the powerpc tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s7qv
-----END PGP SIGNATURE-----
Merge tag 'fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes part 2 from Olof Johansson:
"Here are a few more fixes for 3.8. Two branches of fixes for Samsung
platforms, including fixes for the audio build errors on all non-DT
platforms. There's also a fixup to the sunxi device-tree file renames
due to a bad patch application by me, and a fix for OMAP due to
function renames merged through the powerpc tree."
* tag 'fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: Fix compillation error in mach-omap2/timer.c
ARM: sunxi: rename device tree source files
ARM: EXYNOS: Avoid passing the clks through platform data
ARM: S5PV210: Avoid passing the clks through platform data
ARM: S5P64X0: Add I2S clkdev support
ARM: S5PC100: Add I2S clkdev support
ARM: S3C64XX: Add I2S clkdev support
ARM: EXYNOS: Fix MSHC clocks instance names
ARM: EXYNOS: Fix NULL pointer dereference bug in SMDKV310
ARM: EXYNOS: Fix NULL pointer dereference bug in SMDK4X12
ARM: EXYNOS: Fix NULL pointer dereference bug in Origen
ARM: SAMSUNG: Add missing include guard to gpio-core.h
pinctrl: exynos5440/samsung: Staticize pcfgs
pinctrl: samsung: Fix a typo in pinctrl-samsung.h
ARM: EXYNOS: fix skip scu_enable() for EXYNOS5440
ARM: EXYNOS: fix GIC using for EXYNOS5440
ARM: EXYNOS: fix build error when MFC is not selected
Where we can pass in LOOKUP_DIRECTORY or LOOKUP_REVAL. Any other flags
passed in here are currently ignored.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Commit 787314c35f ("Merge tag 'iommu-updates-v3.8' of
git://git./linux/kernel/git/joro/iommu") did not account for the changed
header location.
The headers were made local to mach-omap2 as they are specific to omap2+
only, and we wanted to get most of the #include <plat/*.h> headers fixed
up anyways for the ARM multiplatform support.
We attempted to avoid this kind of merge conflict early on by setting up
a minimal git branch shared by the arm-soc tree and the iommu tree, but
looks like we still hit a merge issue there as the branches got merged
as various topic branches.
Cc: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the current code, the condition in the if() doesn't make much sense due to
precedence of operators.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Link: http://lkml.kernel.org/r/1356030701-16284-25-git-send-email-sasha.levin@oracle.com
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
A few new features this merge-window. The most important one is
probably, that dma-debug now warns if a dma-handle is not checked with
dma_mapping_error by the device driver. This requires minor changes to
some architectures which make use of dma-debug. Most of these changes
have the respective Acks by the Arch-Maintainers.
Besides that there are updates to the AMD IOMMU driver for refactor the
IOMMU-Groups support and to make sure it does not trigger a hardware
erratum.
The OMAP changes (for which I pulled in a branch from Tony Lindgren's
tree) have a conflict in linux-next with the arm-soc tree. The conflict
is in the file arch/arm/mach-omap2/clock44xx_data.c which is deleted in
the arm-soc tree. It is safe to delete the file too so solve the
conflict. Similar changes are done in the arm-soc tree in the common
clock framework migration. A missing hunk from the patch in the IOMMU
tree will be submitted as a seperate patch when the merge-window is
closed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pPHZ
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"A few new features this merge-window. The most important one is
probably, that dma-debug now warns if a dma-handle is not checked with
dma_mapping_error by the device driver. This requires minor changes
to some architectures which make use of dma-debug. Most of these
changes have the respective Acks by the Arch-Maintainers.
Besides that there are updates to the AMD IOMMU driver for refactor
the IOMMU-Groups support and to make sure it does not trigger a
hardware erratum.
The OMAP changes (for which I pulled in a branch from Tony Lindgren's
tree) have a conflict in linux-next with the arm-soc tree. The
conflict is in the file arch/arm/mach-omap2/clock44xx_data.c which is
deleted in the arm-soc tree. It is safe to delete the file too so
solve the conflict. Similar changes are done in the arm-soc tree in
the common clock framework migration. A missing hunk from the patch
in the IOMMU tree will be submitted as a seperate patch when the
merge-window is closed."
* tag 'iommu-updates-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (29 commits)
ARM: dma-mapping: support debug_dma_mapping_error
ARM: OMAP4: hwmod data: ipu and dsp to use parent clocks instead of leaf clocks
iommu/omap: Adapt to runtime pm
iommu/omap: Migrate to hwmod framework
iommu/omap: Keep mmu enabled when requested
iommu/omap: Remove redundant clock handling on ISR
iommu/amd: Remove obsolete comment
iommu/amd: Don't use 512GB pages
iommu/tegra: smmu: Move bus_set_iommu after probe for multi arch
iommu/tegra: gart: Move bus_set_iommu after probe for multi arch
iommu/tegra: smmu: Remove unnecessary PTC/TLB flush all
tile: dma_debug: add debug_dma_mapping_error support
sh: dma_debug: add debug_dma_mapping_error support
powerpc: dma_debug: add debug_dma_mapping_error support
mips: dma_debug: add debug_dma_mapping_error support
microblaze: dma-mapping: support debug_dma_mapping_error
ia64: dma_debug: add debug_dma_mapping_error support
c6x: dma_debug: add debug_dma_mapping_error support
ARM64: dma_debug: add debug_dma_mapping_error support
intel-iommu: Prevent devices with RMRRs from being placed into SI Domain
...
prom_add_property() has been renamed to of_add_property()
This patch fixes the following comilation error:
arch/arm/mach-omap2/timer.c: In function ‘omap_get_timer_dt’:
arch/arm/mach-omap2/timer.c:178:3: error: implicit declaration of function ‘prom_add_property’ [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[1]: *** [arch/arm/mach-omap2/timer.o] Error 1
make[1]: *** Waiting for unfinished jobs....
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
This is for fix the following build error in dev-audio.c on current Samsung
platforms :-(
arch/arm/mach-exynos/dev-audio.c:58:4: error: unknown field 'src_clk'
specified in initializer
arch/arm/mach-exynos/dev-audio.c:58:4: warning: initialization makes integer
from pointer without a cast [enabled by default]
arch/arm/mach-exynos/dev-audio.c:58:4: warning: (near initialization for
'i2sv5_pdata.type.i2s.idma_addr') [enabled by default]
arch/arm/mach-exynos/dev-audio.c:91:4: error: unknown field 'src_clk'
specified in initializer
arch/arm/mach-exynos/dev-audio.c:91:4: warning: initialization makes integer
from pointer without a cast [enabled by default]
arch/arm/mach-exynos/dev-audio.c:91:4: warning: (near initialization for
'i2sv3_pdata.type.i2s.idma_addr') [enabled by default]
* 'v3.8-samsung-fixes-audio' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Avoid passing the clks through platform data
ARM: S5PV210: Avoid passing the clks through platform data
ARM: S5P64X0: Add I2S clkdev support
ARM: S5PC100: Add I2S clkdev support
ARM: S3C64XX: Add I2S clkdev support
Signed-off-by: Olof Johansson <olof@lixom.net>
From Kukjin Kim:
Here is Samsung fixes-1 for v3.8-rc1.
Most of them are trivial fixes which are for NULL pointer dereference, MSHC
clocks instance names and exynos5440 stuff.
* 'v3.8-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Fix MSHC clocks instance names
ARM: EXYNOS: Fix NULL pointer dereference bug in SMDKV310
ARM: EXYNOS: Fix NULL pointer dereference bug in SMDK4X12
ARM: EXYNOS: Fix NULL pointer dereference bug in Origen
ARM: SAMSUNG: Add missing include guard to gpio-core.h
pinctrl: exynos5440/samsung: Staticize pcfgs
pinctrl: samsung: Fix a typo in pinctrl-samsung.h
ARM: EXYNOS: fix skip scu_enable() for EXYNOS5440
ARM: EXYNOS: fix GIC using for EXYNOS5440
ARM: EXYNOS: fix build error when MFC is not selected
Signed-off-by: Olof Johansson <olof@lixom.net>
This is the rename portion of "ARM: sunxi: Change device tree naming
scheme for sunxi" that were missed when the patch was applied.
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge commit 752451f01c ("Merge branch 'i2c-embedded/for-next' of
git://git.pengutronix.de/git/wsa/linux") resulted in a build breakage
for OMAP
arch/arm/mach-omap2/i2c.c: In function 'omap_pm_set_max_mpu_wakeup_lat_compat':
arch/arm/mach-omap2/i2c.c:130:2: error: implicit declaration of function 'omap_pm_set_max_mpu_wakeup_lat'
make[1]: *** [arch/arm/mach-omap2/i2c.o] Error 1
Fix this by including the appropriate header file with the function
prototype.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This update contains overall only driver-specific fixes.
Slightly large LOC are seen in usb-audio driver for a couple of new
device quirks and cs42l71 ASoC driver for enhanced features.
The others are a few small (regression) fixes HD-audio, and yet other
small / trival ASoC fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=JoY5
-----END PGP SIGNATURE-----
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This update contains overall only driver-specific fixes. Slightly
large LOC are seen in usb-audio driver for a couple of new device
quirks and cs42l71 ASoC driver for enhanced features. The others are
a few small (regression) fixes HD-audio, and yet other small / trival
ASoC fixes."
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Support for Digidesign Mbox 2 USB sound card:
ALSA: HDA: Fix sound resume hang
ALSA: hda - bug fix for invalid connection list of Haswell HDMI codec pins
ALSA: hda - Fix the wrong pincaps set in ALC861VD dallas/hp fixup
ALSA: hda - Set codec->single_adc_amp flag for Realtek codecs
ASoC: atmel-ssc: change disable to disable in dts node
ASoC: Prevent pop_wait overwrite
ALSA: usb-audio: ignore-quirk for HP Wireless Audio
ALSA: hda - Always turn on pins for HDMI/DP
ALSA: hda - Fix pin configuration of HP Pavilion dv7
ASoC: core: Fix splitting of log messages
ASoC: cs42l73: Change VSPIN/VSPOUT to VSPINOUT
ASoC: cs42l73: Add DAPM events for power down.
ASoC: cs42l73: Add DMIC's as DAPM inputs.
ASoC: sigmadsp: Fix endianness conversion issue
ASoC: tpa6130a2: Use devm_* APIs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlDTANQACgkQ31LbvUHyf1dJVQCeOXJokr0cWBPjAN+kXsnhHAAi
130An1kvQDFlZKIGuUqsvADmXpsBMR+8
=bo4L
-----END PGP SIGNATURE-----
Merge tag 'cris-for-linus-3.8' of git://jni.nu/cris
Pull CRIS changes from Jesper Nilsson.
... mainly the UAPI disintegration.
* tag 'cris-for-linus-3.8' of git://jni.nu/cris:
UAPI: Fix up empty files in arch/cris/
CRIS: locking: fix the return value of arch_read_trylock()
CRIS: use kbuild.h instead of defining macros in asm-offset.c
UAPI: (Scripted) Disintegrate arch/cris/include/asm
UAPI: (Scripted) Disintegrate arch/cris/include/arch-v32/arch
UAPI: (Scripted) Disintegrate arch/cris/include/arch-v10/arch
Linus Torvalds