summaryrefslogtreecommitdiffstats
path: root/src/target/firmware/board/gtm900b/init.c
blob: f04d3140b03fff06f0951dfd01c9190c205ed970 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
/* Initialization for the Huawei GTM900-B modem */

/* (C) 2010 by Harald Welte <laforge@gnumonks.org>
 * (C) 2010-19 by Steve Markgraf <steve@steve-m.de>
 *
 * All Rights Reserved
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; either version 2 of the License, or
 * (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License along
 * with this program; if not, write to the Free Software Foundation, Inc.,
 * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
 *
 */

#include <stdint.h>
#include <stdio.h>

#include <debug.h>
#include <ctors.h>
#include <memory.h>
#include <board.h>
#include <keypad.h>
#include <console.h>
#include <flash/cfi_flash.h>
#include <tiffs.h>

#include <calypso/irq.h>
#include <calypso/clock.h>
#include <calypso/dma.h>
#include <calypso/rtc.h>
#include <calypso/timer.h>
#include <uart.h>
#include <calypso/backlight.h>

#include <comm/sercomm.h>
#include <comm/timer.h>

#include <abb/twl3025.h>
#include <rf/trf6151.h>
#include "keymap.h"

#define ARMIO_LATCH_OUT 0xfffe4802
#define IO_CNTL_REG	0xfffe4804
#define ASIC_CONF_REG	0xfffef008
#define IO_CONF_REG	0xfffef00a
#define LPG_LCR_REG	0xfffe7800
#define LPG_PM_REG	0xfffe7801

static void board_io_init(void)
{
	uint16_t reg;

	reg = readw(ASIC_CONF_REG);
	/* Set LPG pin mux for power LED */
	reg |= (1 << 6);
	/* TWL3025: Set SPI+RIF RX clock to rising edge */
	reg |= (1 << 13) | (1 << 14);
	writew(reg, ASIC_CONF_REG);

	/*
	 * Configure Calypso GPIO and multifunction pins the same way
	 * how Huawei's official firmware configures them.
	 */
	writew(0x03F5, IO_CONF_REG);
	writew(0xDC58, IO_CNTL_REG);
	writew(0x0007, ARMIO_LATCH_OUT);

	/* Set LPG output permanently on (power LED) */
	writew(1, LPG_PM_REG);
	writew((1 << 7), LPG_LCR_REG);
}

void board_init(int with_irq)
{
	/* Configure the memory interface */
	calypso_mem_cfg(CALYPSO_nCS0, 3, CALYPSO_MEM_16bit, 1);
	calypso_mem_cfg(CALYPSO_nCS1, 3, CALYPSO_MEM_16bit, 1);
	calypso_mem_cfg(CALYPSO_nCS2, 5, CALYPSO_MEM_16bit, 1);
	calypso_mem_cfg(CALYPSO_nCS3, 5, CALYPSO_MEM_16bit, 1);
	calypso_mem_cfg(CALYPSO_CS4, 0, CALYPSO_MEM_8bit, 1);
	calypso_mem_cfg(CALYPSO_nCS6, 0, CALYPSO_MEM_32bit, 1);
	calypso_mem_cfg(CALYPSO_nCS7, 0, CALYPSO_MEM_32bit, 0);

	/* Set VTCXO_DIV2 = 1, configure PLL for 104 MHz and give ARM half of that */
	calypso_clock_set(2, CALYPSO_PLL13_104_MHZ, ARM_MCLK_DIV_2);

	/* Configure the RHEA bridge with some sane default values */
	calypso_rhea_cfg(0, 0, 0xff, 0, 1, 0, 0);

	/* Initialize board-specific GPIO */
	board_io_init();

	/* Enable bootrom mapping to route exception vectors to RAM */
	calypso_bootrom(with_irq);
	calypso_exceptions_install();

	/* Initialize interrupt controller */
	if (with_irq)
		irq_init();

	sercomm_bind_uart(UART_IRDA);
	cons_bind_uart(UART_MODEM);

	/* initialize IRDA UART to be used for sercomm */
	uart_init(UART_IRDA, with_irq);
	uart_baudrate(UART_IRDA, UART_115200);

	/* Initialize MODEM UART to be used for old-school console code. */
	uart_init(UART_MODEM, with_irq);
	uart_baudrate(UART_MODEM, UART_115200);

	/* Initialize hardware timers */
	hwtimer_init();

	/* Initialize DMA controller */
	dma_init();

	/* Initialize real time clock */
	rtc_init();

	/* Initialize system timers (uses hwtimer 2) */
	timer_init();

	/* Initialize keypad driver */
	keypad_init(keymap, with_irq);

	/* Initialize ABB driver (uses SPI) */
	twl3025_init();
}