|author||Andreas Eversberg <email@example.com>||2016-07-24 20:00:35 +0200|
|committer||Andreas Eversberg <firstname.lastname@example.org>||2016-07-31 14:48:56 +0200|
work on docs
Diffstat (limited to 'docs')
4 files changed, 13 insertions, 5 deletions
diff --git a/docs/a-netz.html b/docs/a-netz.html
index cbef09a..6a961e8 100644
@@ -286,7 +286,7 @@ Instead of transmitting all 4 tones at once, they can be transmitted after each
Each tone is plays for a short time.
After the last tone has been played, base station starts again with the first tone.
My phone also responds to a call, even if the tones cycle rather than sent simultaneously.
-In this case the level of each tone is two times higher (+3 dB), but the peak level is two times lower (-3 dB) than the peak level of 4 simultaneous tones.
+In this case the deviation level of each tone is two times higher (+6 dB). (The level transmitted is two times lower (-6 dB) than the peak level of 4 simultaneous tones. This may help transmitters with deviation limiters to make the phone ring.)
Add command line option "-P 50" to send each tone for 50 milliseconds.
Try something between 20-100 milliseconds, if the phone still doesn't ring.
Be sure to check: Does your transmitter has enough frequency deviation (15 KHz is suggested)? Do you really send the correct number of your phone, check the frequencies of your phone and use "-D 0" option to see what 4 frequencies the base station actually transmits.
diff --git a/docs/index.html b/docs/index.html
index 33178ed..ae452a9 100644
@@ -24,7 +24,15 @@ AMPS (Advanced Mobile Phone Service) ; my radio setup<br>
-A base station implementation of classic mobile networks. All these networks use analog voice transmission. The signaling is done by tones and/or FSK modulated digital messages. It started with the idea to make a base station for the German B-Netz, but more networks followed.
+A base station implementation of classic mobile networks.
+All these networks use analog voice transmission.
+The signaling is done by tones and/or FSK modulated digital messages.
+It started with the idea to make a base station for the German B-Netz, but more networks followed.
+This project is pure software that requires a transmitter and a receiver connected to the sound card of a Linux PC.
+A second sound card or ISDN card is used to route calls from and to the mobile phone.
<h1>*this doc is under construction*</h1>
diff --git a/docs/nmt.html b/docs/nmt.html
index bbad31e..669ff97 100644
@@ -775,7 +775,7 @@ It uses the lower DMS layer to transfer data between network and mobile station
If the phone supports SMS, try sending a test SMS to any number.
Be sure to set the SMSC (Short Message Service Center) to '767'.
This software will detect SMS call when the phone dials '767'.
-If you cannot define the SMSC on your phone, send an SMS and check what number was dialed, then use '-I <number>' to define SMSC at this software.
+If you cannot define the SMSC on your phone, send an SMS and check what number was dialed, then use '-S <number>' or '--smsc-number <number>' to define SMSC at this software.
Also be sure not to enable encryption for SMS.
The process looks like this:
@@ -879,7 +879,7 @@ The process looks like this:
nmt.c:1807 info : SMS for subscriber '3735859'
-SMS sending '1234' -> '3735859': 1234,3735859,This is a test!
+SMS sending '1234' -> '3735859': This is a test!
nmt.c:1597 info : Call to mobile station, paging station id '3735859'
nmt.c:434 info : Entering paging state (try 1), sending call to '3,735859'.
nmt.c:443 info : Paging on our channel 1.
diff --git a/docs/setup.html b/docs/setup.html
index 1d17925..08c0c18 100644
@@ -112,7 +112,7 @@ If you don't have the knowledge about power supplies, ask an expert to help you.
Early tests were done without any wiring between radios and sound adapter.
-This may worked for early tests with the B-Netz, but turned out to be a pain in the as.
+This may worked for early tests with the B-Netz, but turned out to be a pain in the ass.
It is not possible to keep the levels and avoid feed-backs.