aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/mmc/core/mmc.c
AgeCommit message (Collapse)AuthorFilesLines
2012-02-13mmc: core: Fix comparison issue in mmc_compare_ext_csdsJurgen Heeks1-2/+2
Found this issue during code review. Actually, there are two issues which both compensate together in lucky case. In unlucky case the bus width probing might not work as expected. Signed-off-by: Jurgen Heeks <jurgen.heeks@nokia.com> Reviewed-by: Namjae Jeon <linkinjeon@gmail.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-02-13mmc: core: Fix PowerOff Notify suspend/resumeGirish K S1-5/+12
Modified the mmc_poweroff to resume before sending the poweroff notification command. In sleep mode only AWAKE and RESET commands are allowed, so before sending the poweroff notification command resume from sleep mode and then send the notification command. PowerOff Notify is tested on a Synopsis Designware Host Controller (eMMC 4.5). The suspend to RAM and resume works fine. Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Tested-by: Girish K S <girish.shivananjappa@linaro.org> Reviewed-by: Saugata Das <saugata.das@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-02-13mmc: core: Fix low speed mmc card detection failureGirish K S1-2/+3
This patch fixes the failure of low speed mmc card detection. Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-12mmc: core: HS200 mode support for eMMC 4.5Girish K S1-9/+153
This patch adds the support of the HS200 bus speed for eMMC 4.5 devices. The eMMC 4.5 devices have support for 200MHz bus speed. The function prototype of the tuning function is modified to handle the tuning command number which is different in sd and mmc case. Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Signed-off-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-12mmc: core: Separate the timeout value for cache-ctrlSeungwon Jeon1-2/+11
Turning the cache off implies flushing cache which doesn't define maximum timeout unlike cache-on. This patch will apply the generic CMD6 timeout only for cache-on. Additionally the kernel message is added for checking failure case of cache-on. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-11mmc: core: Fix voltage select in DDR modeGirish K S1-1/+1
This patch fixes the wrong comparison before setting the interface voltage in DDR mode. The assignment to the variable ddr before comaprison is either ddr = MMC_1_2V_DDR_MODE; or ddr == MMC_1_8V_DDR_MODE. But the comparison is done with the extended csd value if ddr == EXT_CSD_CARD_TYPE_DDR_1_2V. Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Acked-by: Subhash Jadavani <subhashj@codeaurora.org> Acked-by: Philip Rakity <prakity@marvell.com> Cc: <stable@kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-11mmc: boot partition ro lock supportJohan Rudholm1-2/+12
Enable boot partitions to be read-only locked until next power on via a sysfs entry. There will be one sysfs entry for each boot partition: /sys/block/mmcblkXbootY/ro_lock_until_next_power_on Each boot partition is locked by writing 1 to its file. Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com> Signed-off-by: John Beckett <john.beckett@stericsson.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-11mmc: allow upper layers to know immediately if card has been removedAdrian Hunter1-1/+11
Add a function mmc_detect_card_removed() which upper layers can use to determine immediately if a card has been removed. This function should be called after an I/O request fails so that all queued I/O requests can be errored out immediately instead of waiting for the card device to be removed. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Sujit Reddy Thumma <sthumma@codeaurora.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-12-10mmc: core: Fix power_off_notify during suspendGirish K S1-1/+1
The eMMC 4.5 devices respond to only RESET and AWAKE command in the sleep state. Hence the mmc switch command to notify power off state should be sent before the device enters sleep state. This patch fixes the same. Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-12-10mmc: core: Fix setting power notify state variable for non-eMMCGirish K S1-3/+7
This patch skips the setting of the power notify state variable for non eMMC 4.5 devices. Also fixes the problem of omap_hsmmc noisy/broken for suspend resume reported by Kevin Hilman. Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Acked-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-31mmc: Fix implicit use of stat.h header in associated filesPaul Gortmaker1-0/+1
Once the implicit use of module.h is prevented, these files will fail to find the stat.h header content. Fix up the implicit usage expectations in advance of the cleanup. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2011-10-27mmc: core: Cleanup eMMC4.5 conditionalsSeungwon Jeon1-11/+9
Code cleanup, putting all eMMC 4.5 detection cases together. This patch removes one if-statement and assembles all. And it also removes variable initialization below else-statement -- all members of card structure are already set to zero at card-init. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: core: support HPI send commandJaehoon Chung1-0/+31
HPI command is defined in eMMC4.41. This feature is important for eMMC4.5 devices. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: core: Add cache control for eMMC4.5 deviceSeungwon Jeon1-0/+23
This patch adds cache feature of eMMC4.5 Spec. If device supports cache capability, host can utilize some specific operations. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: core: Modify the timeout value for writing power classSeungwon Jeon1-1/+1
This patch will apply the generic CMD6 timeout to switch command for power class. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: core: new discard feature support at eMMC v4.5Kyungmin Park1-0/+4
MMC v4.5 supports the DISCARD feature (CMD38). It's different from trim and there's no check bit. Currently it's only supported at v4.5. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: core: Add Power Off Notify Feature eMMC 4.5Girish K S1-2/+21
This patch adds support for the power off notify feature, available in eMMC 4.5 devices. If the host has support for this feature, then the mmc core will notify the device by setting the POWER_OFF_NOTIFICATION byte in the extended csd register with a value of 1 (POWER_ON). For suspend mode short timeout is used, whereas for the normal poweroff long timeout is used. Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: replace printk with appropriate display macroGirish K S1-12/+12
All the files using printk function for displaying kernel messages in the mmc driver have been replaced with corresponding macro. Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: core: Add default timeout value for CMD6Seungwon Jeon1-4/+12
EXT_CSD[248] includes the default maximum timeout for CMD6. This field is added at eMMC4.5 Spec. And it can be used for default timeout except for some operations which don't define the timeout (i.e. background operation, sanitize, flush cache) in eMMC4.5 Spec. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: core: general purpose MMC partition support.Namjae Jeon1-4/+48
It allows gerneral purpose partitions in MMC Device. And I try to simply make mmc_blk_alloc_parts using mmc_part structure suggested by Andrei Warkentin. After patching, we see general purpose partitions like this: > cat /proc/partitions 179 0 847872 mmcblk0 179 192 4096 mmcblk0gp3 179 160 4096 mmcblk0gp2 179 128 4096 mmcblk0gp1 179 96 1052672 mmcblk0gp0 179 64 1024 mmcblk0boot1 179 32 1024 mmcblk0boot0 Signed-off-by: Namjae Jeon <linkinjeon@gmail.com> Acked-by: Andrei Warkentin <awarkentin@vmware.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: core: ext_csd.raw_* used in comparison but never setAndrei Warkentin1-0/+2
f39b2dd9d ("mmc: core: Bus width testing needs to handle suspend/resume") added code to only compare read-only ext_csd fields in bus width testing code, yet it's comparing some fields that are never set. The affected fields are ext_csd.raw_erased_mem_count and ext_csd.raw_partition_support. Signed-off-by: Andrei Warkentin <andrey.warkentin@gmail.com> Acked-by: Philip Rakity <prakity@marvell.com> Cc: <stable@kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: core: eMMC 4.5 Power Class Selection FeatureGirish K S1-0/+96
This patch adds the power class selection feature available for mmc versions 4.0 and above. During the enumeration stage before switching to the lower data bus, check if the power class is supported for the current bus width. If the power class is available then switch to the power class and use the higher data bus. If power class is not supported then switch to the lower data bus in a worst case. Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: core: add eMMC hardware reset supportAdrian Hunter1-1/+3
eMMC's may have a hardware reset line. This patch provides a host controller operation to implement hardware reset and a function to reset and reinitialize the card. Also, for MMC, the reset is always performed before initialization. The host must set the new host capability MMC_CAP_HW_RESET to enable hardware reset. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: core: Set correct bus mode before card initStefan Nilsson XK1-0/+8
Earlier all cards where initiated with bus mode set as OPENDRAIN, and then later switched to PUSHPULL. According to the MMC/SD/SDIO specifications only MMC cards use OPENDRAIN during init. For both SD and SDIO the bus mode shall be PUSHPULL before attempting to init the card. The consequence of having incorrect bus mode can lead to not being able to detect the card. Therefore the default behavior have now been changed to PUSHPULL in mmc_power_up, and will only be temporarily switched when trying to attach or init a MMC card. Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com> Signed-off-by: Ulf HANSSON <ulf.hansson@stericsson.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: core: Fix hangs related to insert/remove of cardsUlf Hansson1-0/+1
During a rescan operation mmc_attach(sd|mmc|sdio) functions are called. The error handling in these function can trigger a detach of the bus, which also meant a power off. This is not notified by the rescan operation which then continues to the next attach function. If a power off has been done, the framework must never send any new commands to the host driver, without first doing a new power up. This will most likely trigger any host driver to hang. Moving power off out of detach and instead handle power off separately when it is actually needed, solves the issue. Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Cc: <stable@kernel.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: core: Put eMMC in Sleep mode before suspendBalaji T K1-2/+7
Put MMC to sleep if it supports SLEEP/AWAKE (CMD5) in the mmc suspend so that Vcc (NAND core) can be cut to minimize power consumption. eMMC put into SLEEP can respond to CMD0 or H/W reset or CMD5. Current implemention on resume from suspend relies on CMD0 in mmc_init_card to get out of SLEEP mode. Signed-off-by: Balaji T K <balajitk@ti.com> Acked-by: Venkatraman S <svenkatr@ti.com> Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13mmc: core: Detect eMMC v4.5 ext_csd entriesKyungmin Park1-1/+1
The eMMC v4.5 Spec is released now: EXT_CSD_REV Extended CSD Revision 255-7 Reserved 6 Revision 1.6 (for MMC v4.5) 5 Revision 1.5 (for MMV v4.41) ... Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-13mmc: core: Bus width testing needs to handle suspend/resumePhilip Rakity1-27/+50
On reading the ext_csd for the first time (in 1 bit mode), save the ext_csd information needed for bus width compare. On every pass we make re-reading the ext_csd, compare the data against the saved ext_csd data. This fixes a regression introduced in 3.0-rc1 by 08ee80cc397ac1a3 ("mmc: core: eMMC bus width may not work on all platforms"), which incorrectly assumed we would be re-reading the ext_csd at resume- time. Signed-off-by: Philip Rakity <prakity@marvell.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-05-25mmc: core: eMMC bus width may not work on all platformsPhilip Rakity1-10/+102
CMD19 -- The offical way to validate bus widths from the JEDEC spec does not work on all platforms. Some platforms that use PCI/PCIe to connect their SD controllers are known to fail. If the quirk MMC_BUS_WIDTH_TEST is not defined we try to figure out the bus width by reading the ext_csd at different bus widths and compare this against the ext_csd read in 1 bit mode. If no ext_csd is available we default to 1 bit operations. Code has been tested on mmp2 against 8 bit eMMC and Transcend 2GB card that is known to not work in 4 bit mode. The physical pins on the card are not present to support 4 bit operation. Signed-off-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-05-24mmc: core: add support for eMMC Dual Data RatePhilip Rakity1-5/+30
eMMC voltage change not required for 1.8V. 3.3V and 1.8V vcc are capable of doing DDR. vccq of 1.8v is not required. Signed-off-by: Philip Rakity <prakity@marvell.com> Reviewed-by: Arindam Nath <arindam.nath@amd.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-05-24mmc: MMC boot partitions support.Andrei Warkentin1-5/+17
Allows device MMC boot partitions to be accessed. MMC partitions are treated effectively as separate block devices on the same MMC card. Signed-off-by: Andrei Warkentin <andreiw@motorola.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-05-24mmc: core: Allow setting CMD timeout for CMD6 (SWITCH).Andrei Warkentin1-6/+8
CMD6 is an R1B-type command, where DAT is used as busy. Depending on register written using CMD6, timeout value can be different as per spec. Signed-off-by: Andrei Warkentin <andreiw@motorola.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-05-24mmc: Reliable write support.Andrei Warkentin1-0/+5
Allows reliable writes to be used for MMC writes. Reliable writes are used to service write REQ_FUA/REQ_META requests. Handles both the legacy and the enhanced reliable write support in MMC cards. Signed-off-by: Andrei Warkentin <andreiw@motorola.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-05-24mmc: Ensure linux starts in eMMC user partitionPhilip Rakity1-0/+10
uBoot sometimes leaves eMMC pointing to the private boot partition. Ensure we always start looking at the user partition. Signed-off-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Bruce Clemens <bpclemens@marvell.com> Signed-off-by: Mark F. Brown <markb@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-03-31Fix common misspellingsLucas De Marchi1-1/+1
Fixes generated by 'codespell' and manually reviewed. Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-16mmc: check if mmc cards < 2GB do sector addressingPhilip Rakity1-1/+11
Some TOSHIBA MMC cards only support sector addressing even though the size is < 2GB. According to JEDEC Spec JESD84-A441-1 the ocr register (bits 30, 29) determine byte/sector mode. Use them. Signed-off-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-03-15mmc: export eMMC4.4 enhanced area details to sysfsChuanxiao Dong1-0/+74
Enhanced area feature is a new feature defined in eMMC4.4 standard. This user data area provides higher performance/reliability, at the expense of using twice the effective media space due to the area using SLC. The MMC driver now reads out the enhanced area offset and size and adds them to the device attributes in sysfs. Enabling the enhanced area can only be done once, and should be done in manufacturing. To use this feature, bit ERASE_GRP_DEF should also be set. Documentation/ABI/testing/sysfs-devices-mmc describes the two new attributes. Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com> Reviewed-by: Chris Ball <cjb@laptop.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-01-08mmc: Fix sd/sdio/mmc initialization frequency retriesAndy Ross1-4/+9
Rewrite and clean up mmc_rescan() to properly retry frequencies lower than 400kHz. Failures can happen both in sd_send_* calls and mmc_attach_*. Break out "mmc_rescan_try_freq" from the frequency selection loop. Symmetrize claim/release logic in mmc_attach_* API, and move the sd_send_* calls there to make mmc_rescan easier to read. Signed-off-by: Andy Ross <andy.ross@windriver.com> Reviewed-and-Tested-by: Hein Tibosch <hein_tibosch@yahoo.es> Reviewed-by: Chris Ball <cjb@laptop.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-01-08mmc: fix mmc_set_bus_width_ddr() call without bus-width-test capTakashi Iwai1-2/+2
With the bus-width test patch, mmc_set_bus_width*() isn't called properly when the driver doesn't set MMC_CAP_BUS_WIDTH and no DDR mode. This patch fixes the regression by moving the call up before the cap test. Signed-off-by: Takashi Iwai <tiwai@suse.de> Reviewed-by: Chris Ball <cjb@laptop.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-01-08mmc: Test bus-width for old MMC devicesAries Lee1-29/+47
Some old MMC devices fail with the 4/8 bits the driver tries to use exclusively. This patch adds a test for the given bus setup and falls back to the lower bit mode (until 1-bit mode) when the test fails. [Major rework and refactoring by tiwai] [Quirk addition and many fixes by prakity] Signed-off-by: Aries Lee <arieslee@jmicron.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Philip Rakity <prakity@marvell.com> Tested-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-01-08mmc: Add support for JMicron 388 SD/MMC controllerTakashi Iwai1-0/+2
JMicron 388 SD/MMC combo controller supports the 1.8V low-voltage for SD, but MMC doesn't work with the low-voltage, resulting in an error at probing. This patch adds the support for multiple voltage mask per device type, so that SD works with 1.8V while MMC forces 3.3V. Here new ocr_avail_* fields for each device are introduced, so that the actual OCR mask is switched dynamically. Also, the restriction of low-voltage in core/sd.c is removed when the bit is allowed explicitly via ocr_avail_sd mask. This patch was rewritten from scratch based on Aries' original code. Signed-off-by: Aries Lee <arieslee@jmicron.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Reviewed-by: Chris Ball <cjb@laptop.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-11-07mmc: Fix printing of card DDR typePhilip Rakity1-2/+6
We should not call mmc_card_set_ddr_mode() if we are in single data mode. This sets DDR and causes the kernel log to say the card is DDR when it is not. Explicitly set ddr to 0 rather then rely on MMC_SDR_MODE being 0 when doing the checks. Signed-off-by: Philip Rakity <prakity@marvell.com> Acked-by: Linus Walleij <linus.walleij@stericsson.com> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc: propagate power save/restore ops return valueOhad Ben-Cohen1-2/+6
Allow power save/restore and their relevant mmc_bus_ops handlers exit with a return value. Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com> Tested-by: Luciano Coelho <luciano.coelho@nokia.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc: refine DDR supportAdrian Hunter1-3/+3
One flaw with DDR support is that MMC core does not inform the driver which DDR mode it has selected. This patch expands the ios->ddr flag to do that. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc: Fixes for Dual Data Rate (DDR) supportAdrian Hunter1-10/+11
The DDR support patch needs the following fixes: - The block driver does not need to know about DDR, any more than it needs to know about bus width. - Not only the card must be switched to DDR mode. The host controller must also be configured, which is done through the 'set_ios()' function. - Do not set the DDR mode state until after the switch command is successful. - Setting block length is not supported in DDR mode. Make that a core function and change the other place it is used (mmc_test) also. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc: MMC 4.4 DDR supportHanumath Prasad1-2/+35
Add support for Dual Data Rate MMC cards as defined in the 4.4 specification. Signed-off-by: Hanumath Prasad <hanumath.prasad@stericsson.com> Cc: linux-mmc@vger.kernel.org Acked-by: Linus Walleij <linus.walleij@stericsson.com> Tested-by Zhangfei Gao <zhangfei.gao@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc: Add helper function to check if a card is removableMatt Fleming1-1/+1
There are two checks that need to be made when determining whether a card is removable. A host controller may set MMC_CAP_NONREMOVABLE if the controller does not support removing cards (e.g. eMMC), in which case the card is physically non-removable. Also the 'mmc_assume_removable' module parameter can be configured at module load time, in which case the card may be logically non-removable. A helper function keeps the logic in one place so that code always checks both conditions. Because this new function is likely to be called from modules we now need to export the mmc_assume_removable symbol. Signed-off-by: Matt Fleming <matt@console-pimps.org> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-08-12mmc: add erase, secure erase, trim and secure trim operationsAdrian Hunter1-1/+46
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4 cards can support secure erase, trim and secure trim operations that are all variants of the basic erase command. SD/MMC device attributes "erase_size" and "preferred_erase_size" have been added. "erase_size" is the minimum size, in bytes, of an erase operation. For MMC, "erase_size" is the erase group size reported by the card. Note that "erase_size" does not apply to trim or secure trim operations where the minimum size is always one 512 byte sector. For SD, "erase_size" is 512 if the card is block-addressed, 0 otherwise. SD/MMC cards can erase an arbitrarily large area up to and including the whole card. When erasing a large area it may be desirable to do it in smaller chunks for three reasons: 1. A single erase command will make all other I/O on the card wait. This is not a problem if the whole card is being erased, but erasing one partition will make I/O for another partition on the same card wait for the duration of the erase - which could be a several minutes. 2. To be able to inform the user of erase progress. 3. The erase timeout becomes too large to be very useful. Because the erase timeout contains a margin which is multiplied by the size of the erase area, the value can end up being several minutes for large areas. "erase_size" is not the most efficient unit to erase (especially for SD where it is just one sector), hence "preferred_erase_size" provides a good chunk size for erasing large areas. For MMC, "preferred_erase_size" is the high-capacity erase size if a card specifies one, otherwise it is based on the capacity of the card. For SD, "preferred_erase_size" is the allocation unit size specified by the card. "preferred_erase_size" is in bytes. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Acked-by: Jens Axboe <axboe@kernel.dk> Cc: Kyungmin Park <kmpark@infradead.org> Cc: Madhusudhan Chikkature <madhu.cr@ti.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ben Gardiner <bengardiner@nanometrics.ca> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11mmc: only set blockaddressed for > 2GiB cardsHanumath Prasad1-1/+3
A non-zero value of SEC_COUNT does not indicate that the card is sector addressed. According to the MMC specification, cards with a density greater than 2GiB are sector addressed. Acked-by: Linus Walleij <linus.walleij@stericsson.com> Signed-off-by: Hanumath Prasad <hanumath.prasad@stericsson.com> Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11mmc: recognize CSD structureKyungmin Park1-7/+19
The eMMC spec 4.4 and 4.3 + additional feature chips has CSD structure version 3 and version 3 have to check the CSD_STRUCTURE byte in the EXT_CSD register. Also fix EXT_CSD revision message. [akpm@linux-foundation.org: fix comment, per Chris Ball] Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Cc: Adrian Hunter <adrian.hunter@nokia.com> Cc: Chris Ball <cjb@laptop.org> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>