aboutsummaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/regulator
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/regulator')
-rw-r--r--Documentation/devicetree/bindings/regulator/88pm860x.txt30
-rw-r--r--Documentation/devicetree/bindings/regulator/fixed-regulator.txt2
-rw-r--r--Documentation/devicetree/bindings/regulator/gpio-regulator.txt37
-rw-r--r--Documentation/devicetree/bindings/regulator/max8907.txt69
-rw-r--r--Documentation/devicetree/bindings/regulator/max8925-regulator.txt40
-rw-r--r--Documentation/devicetree/bindings/regulator/max8997-regulator.txt146
-rw-r--r--Documentation/devicetree/bindings/regulator/regulator.txt8
-rw-r--r--Documentation/devicetree/bindings/regulator/tps65217.txt78
-rw-r--r--Documentation/devicetree/bindings/regulator/tps6586x.txt42
-rw-r--r--Documentation/devicetree/bindings/regulator/twl-regulator.txt1
-rw-r--r--Documentation/devicetree/bindings/regulator/vexpress.txt32
11 files changed, 482 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/regulator/88pm860x.txt b/Documentation/devicetree/bindings/regulator/88pm860x.txt
new file mode 100644
index 00000000000..1267b3e1a2c
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/88pm860x.txt
@@ -0,0 +1,30 @@
+Marvell 88PM860x regulator
+
+Required properties:
+- compatible: "marvell,88pm860x"
+- reg: I2C slave address
+- regulators: A node that houses a sub-node for each regulator within the
+ device. Each sub-node is identified using the regulator-compatible
+ property, with valid values listed below.
+
+Example:
+
+ pmic: 88pm860x@34 {
+ compatible = "marvell,88pm860x";
+ reg = <0x34>;
+
+ regulators {
+ BUCK1 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ BUCK3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt
index 2f5b6b1ba15..4fae41d5479 100644
--- a/Documentation/devicetree/bindings/regulator/fixed-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/fixed-regulator.txt
@@ -10,6 +10,7 @@ Optional properties:
If this property is missing, the default assumed is Active low.
- gpio-open-drain: GPIO is open drain type.
If this property is missing then default assumption is false.
+-vin-supply: Input supply name.
Any property defined as part of the core regulator
binding, defined in regulator.txt, can also be used.
@@ -29,4 +30,5 @@ Example:
enable-active-high;
regulator-boot-on;
gpio-open-drain;
+ vin-supply = <&parent_reg>;
};
diff --git a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt
new file mode 100644
index 00000000000..63c659800c0
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt
@@ -0,0 +1,37 @@
+GPIO controlled regulators
+
+Required properties:
+- compatible : Must be "regulator-gpio".
+- states : Selection of available voltages and GPIO configs.
+ if there are no states, then use a fixed regulator
+
+Optional properties:
+- enable-gpio : GPIO to use to enable/disable the regulator.
+- gpios : GPIO group used to control voltage.
+- startup-delay-us : Startup time in microseconds.
+- enable-active-high : Polarity of GPIO is active high (default is low).
+
+Any property defined as part of the core regulator binding defined in
+regulator.txt can also be used.
+
+Example:
+
+ mmciv: gpio-regulator {
+ compatible = "regulator-gpio";
+
+ regulator-name = "mmci-gpio-supply";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2600000>;
+ regulator-boot-on;
+
+ enable-gpio = <&gpio0 23 0x4>;
+ gpios = <&gpio0 24 0x4
+ &gpio0 25 0x4>;
+ states = <1800000 0x3
+ 2200000 0x2
+ 2600000 0x1
+ 2900000 0x0>;
+
+ startup-delay-us = <100000>;
+ enable-active-high;
+ };
diff --git a/Documentation/devicetree/bindings/regulator/max8907.txt b/Documentation/devicetree/bindings/regulator/max8907.txt
new file mode 100644
index 00000000000..371eccd1cd6
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/max8907.txt
@@ -0,0 +1,69 @@
+MAX8907 regulator
+
+Required properties:
+- compatible: "maxim,max8907"
+- reg: I2C slave address
+- interrupts: The interrupt output of the controller
+- mbatt-supply: The input supply for MBATT, BBAT, SDBY, VRTC.
+- in-v1-supply: The input supply for SD1.
+- in-v2-supply: The input supply for SD2.
+- in-v3-supply: The input supply for SD3.
+- in1-supply: The input supply for LDO1.
+...
+- in20-supply: The input supply for LDO20.
+- regulators: A node that houses a sub-node for each regulator within the
+ device. Each sub-node is identified using the node's name (or the deprecated
+ regulator-compatible property if present), with valid values listed below.
+ The content of each sub-node is defined by the standard binding for
+ regulators; see regulator.txt.
+
+Optional properties:
+- maxim,system-power-controller: Boolean property indicating that the PMIC
+ controls the overall system power.
+
+The valid names for regulators are:
+
+ sd1, sd2, sd3, ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7, ldo8, ldo9, ldo10,
+ ldo11, ldo12, ldo13, ldo14, ldo15, ldo16, ldo17, ldo18, ldo19, ldo20, out5v,
+ out33v, bbat, sdby, vrtc.
+
+Example:
+
+ max8907@3c {
+ compatible = "maxim,max8907";
+ reg = <0x3c>;
+ interrupts = <0 86 0x4>;
+
+ maxim,system-power-controller;
+
+ mbatt-supply = <&some_reg>;
+ in-v1-supply = <&mbatt_reg>;
+ ...
+ in1-supply = <&mbatt_reg>;
+ ...
+
+ regulators {
+ mbatt_reg: mbatt {
+ regulator-name = "vbat_pmu";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ sd1 {
+ regulator-name = "nvvdd_sv1,vdd_cpu_pmu";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ sd2 {
+ regulator-name = "nvvdd_sv2,vdd_core";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+...
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/regulator/max8925-regulator.txt b/Documentation/devicetree/bindings/regulator/max8925-regulator.txt
new file mode 100644
index 00000000000..0057695aae8
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/max8925-regulator.txt
@@ -0,0 +1,40 @@
+Max8925 Voltage regulators
+
+Required nodes:
+-nodes:
+ - SDV1 for SDV SDV1
+ - SDV2 for SDV SDV2
+ - SDV3 for SDV SDV3
+ - LDO1 for LDO LDO1
+ - LDO2 for LDO LDO2
+ - LDO3 for LDO LDO3
+ - LDO4 for LDO LDO4
+ - LDO5 for LDO LDO5
+ - LDO6 for LDO LDO6
+ - LDO7 for LDO LDO7
+ - LDO8 for LDO LDO8
+ - LDO9 for LDO LDO9
+ - LDO10 for LDO LDO10
+ - LDO11 for LDO LDO11
+ - LDO12 for LDO LDO12
+ - LDO13 for LDO LDO13
+ - LDO14 for LDO LDO14
+ - LDO15 for LDO LDO15
+ - LDO16 for LDO LDO16
+ - LDO17 for LDO LDO17
+ - LDO18 for LDO LDO18
+ - LDO19 for LDO LDO19
+ - LDO20 for LDO LDO20
+
+Optional properties:
+- Any optional property defined in bindings/regulator/regulator.txt
+
+Example:
+
+ SDV1 {
+ regulator-min-microvolt = <637500>;
+ regulator-max-microvolt = <1425000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
diff --git a/Documentation/devicetree/bindings/regulator/max8997-regulator.txt b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt
new file mode 100644
index 00000000000..9fd69a18b0b
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/max8997-regulator.txt
@@ -0,0 +1,146 @@
+* Maxim MAX8997 Voltage and Current Regulator
+
+The Maxim MAX8997 is a multi-function device which includes volatage and
+current regulators, rtc, charger controller and other sub-blocks. It is
+interfaced to the host controller using a i2c interface. Each sub-block is
+addressed by the host system using different i2c slave address. This document
+describes the bindings for 'pmic' sub-block of max8997.
+
+Required properties:
+- compatible: Should be "maxim,max8997-pmic".
+- reg: Specifies the i2c slave address of the pmic block. It should be 0x66.
+
+- max8997,pmic-buck1-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+ units for buck1 when changing voltage using gpio dvs. Refer to [1] below
+ for additional information.
+
+- max8997,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+ units for buck2 when changing voltage using gpio dvs. Refer to [1] below
+ for additional information.
+
+- max8997,pmic-buck5-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
+ units for buck5 when changing voltage using gpio dvs. Refer to [1] below
+ for additional information.
+
+[1] If none of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional
+ property is specified, the 'max8997,pmic-buck[1/2/5]-dvs-voltage'
+ property should specify atleast one voltage level (which would be a
+ safe operating voltage).
+
+ If either of the 'max8997,pmic-buck[1/2/5]-uses-gpio-dvs' optional
+ property is specified, then all the eigth voltage values for the
+ 'max8997,pmic-buck[1/2/5]-dvs-voltage' should be specified.
+
+Optional properties:
+- interrupt-parent: Specifies the phandle of the interrupt controller to which
+ the interrupts from max8997 are delivered to.
+- interrupts: Interrupt specifiers for two interrupt sources.
+ - First interrupt specifier is for 'irq1' interrupt.
+ - Second interrupt specifier is for 'alert' interrupt.
+- max8997,pmic-buck1-uses-gpio-dvs: 'buck1' can be controlled by gpio dvs.
+- max8997,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs.
+- max8997,pmic-buck5-uses-gpio-dvs: 'buck5' can be controlled by gpio dvs.
+
+Additional properties required if either of the optional properties are used:
+- max8997,pmic-ignore-gpiodvs-side-effect: When GPIO-DVS mode is used for
+ multiple bucks, changing the voltage value of one of the bucks may affect
+ that of another buck, which is the side effect of the change (set_voltage).
+ Use this property to ignore such side effects and change the voltage.
+
+- max8997,pmic-buck125-default-dvs-idx: Default voltage setting selected from
+ the possible 8 options selectable by the dvs gpios. The value of this
+ property should be between 0 and 7. If not specified or if out of range, the
+ default value of this property is set to 0.
+
+- max8997,pmic-buck125-dvs-gpios: GPIO specifiers for three host gpio's used
+ for dvs. The format of the gpio specifier depends in the gpio controller.
+
+Regulators: The regulators of max8997 that have to be instantiated should be
+included in a sub-node named 'regulators'. Regulator nodes included in this
+sub-node should be of the format as listed below.
+
+ regulator_name {
+ standard regulator bindings here
+ };
+
+The following are the names of the regulators that the max8997 pmic block
+supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
+as per the datasheet of max8997.
+
+ - LDOn
+ - valid values for n are 1 to 18 and 21
+ - Example: LDO0, LD01, LDO2, LDO21
+ - BUCKn
+ - valid values for n are 1 to 7.
+ - Example: BUCK1, BUCK2, BUCK3, BUCK7
+
+ - ENVICHG: Battery Charging Current Monitor Output. This is a fixed
+ voltage type regulator
+
+ - ESAFEOUT1: (ldo19)
+ - ESAFEOUT2: (ld020)
+
+ - CHARGER_CV: main battery charger voltage control
+ - CHARGER: main battery charger current control
+ - CHARGER_TOPOFF: end of charge current threshold level
+
+The bindings inside the regulator nodes use the standard regulator bindings
+which are documented elsewhere.
+
+Example:
+
+ max8997_pmic@66 {
+ compatible = "maxim,max8997-pmic";
+ interrupt-parent = <&wakeup_eint>;
+ reg = <0x66>;
+ interrupts = <4 0>, <3 0>;
+
+ max8997,pmic-buck1-uses-gpio-dvs;
+ max8997,pmic-buck2-uses-gpio-dvs;
+ max8997,pmic-buck5-uses-gpio-dvs;
+
+ max8997,pmic-ignore-gpiodvs-side-effect;
+ max8997,pmic-buck125-default-dvs-idx = <0>;
+
+ max8997,pmic-buck125-dvs-gpios = <&gpx0 0 1 0 0>, /* SET1 */
+ <&gpx0 1 1 0 0>, /* SET2 */
+ <&gpx0 2 1 0 0>; /* SET3 */
+
+ max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
+ <1250000>, <1200000>,
+ <1150000>, <1100000>,
+ <1000000>, <950000>;
+
+ max8997,pmic-buck2-dvs-voltage = <1100000>, <1100000>,
+ <1100000>, <1100000>,
+ <1000000>, <1000000>,
+ <1000000>, <1000000>;
+
+ max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>,
+ <1200000>, <1200000>;
+
+ regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ABB_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "VDD_ALIVE_1.1V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "VDD_ARM_1.2V";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt
index 5b7a408acda..ecfc6ccd67e 100644
--- a/Documentation/devicetree/bindings/regulator/regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/regulator.txt
@@ -10,6 +10,14 @@ Optional properties:
- regulator-always-on: boolean, regulator should never be disabled
- regulator-boot-on: bootloader/firmware enabled regulator
- <name>-supply: phandle to the parent supply/regulator node
+- regulator-ramp-delay: ramp delay for regulator(in uV/uS)
+
+Deprecated properties:
+- regulator-compatible: If a regulator chip contains multiple
+ regulators, and if the chip's binding contains a child node that
+ describes each regulator, then this property indicates which regulator
+ this child node is intended to configure. If this property is missing,
+ the node's name will be used instead.
Example:
diff --git a/Documentation/devicetree/bindings/regulator/tps65217.txt b/Documentation/devicetree/bindings/regulator/tps65217.txt
new file mode 100644
index 00000000000..4f05d208c95
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/tps65217.txt
@@ -0,0 +1,78 @@
+TPS65217 family of regulators
+
+Required properties:
+- compatible: "ti,tps65217"
+- reg: I2C slave address
+- regulators: list of regulators provided by this controller, must be named
+ after their hardware counterparts: dcdc[1-3] and ldo[1-4]
+- regulators: This is the list of child nodes that specify the regulator
+ initialization data for defined regulators. Not all regulators for the given
+ device need to be present. The definition for each of these nodes is defined
+ using the standard binding for regulators found at
+ Documentation/devicetree/bindings/regulator/regulator.txt.
+
+Optional properties:
+- ti,pmic-shutdown-controller: Telling the PMIC to shutdown on PWR_EN toggle.
+
+ The valid names for regulators are:
+ tps65217: dcdc1, dcdc2, dcdc3, ldo1, ldo2, ldo3 and ldo4
+
+Each regulator is defined using the standard binding for regulators.
+
+Example:
+
+ tps: tps@24 {
+ compatible = "ti,tps65217";
+ ti,pmic-shutdown-controller;
+
+ regulators {
+ dcdc1_reg: dcdc1 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ dcdc2_reg: dcdc2 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ dcdc3_reg: dcc3 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: ldo1 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo2_reg: ldo2 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: ldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4_reg: ldo4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/regulator/tps6586x.txt b/Documentation/devicetree/bindings/regulator/tps6586x.txt
index 0fcabaa3baa..8b40cac24d9 100644
--- a/Documentation/devicetree/bindings/regulator/tps6586x.txt
+++ b/Documentation/devicetree/bindings/regulator/tps6586x.txt
@@ -6,11 +6,31 @@ Required properties:
- interrupts: the interrupt outputs of the controller
- #gpio-cells: number of cells to describe a GPIO
- gpio-controller: mark the device as a GPIO controller
-- regulators: list of regulators provided by this controller, must be named
- after their hardware counterparts: sm[0-2], ldo[0-9] and ldo_rtc
+- regulators: A node that houses a sub-node for each regulator within the
+ device. Each sub-node is identified using the node's name (or the deprecated
+ regulator-compatible property if present), with valid values listed below.
+ The content of each sub-node is defined by the standard binding for
+ regulators; see regulator.txt.
+ sys, sm[0-2], ldo[0-9] and ldo_rtc
+- sys-supply: The input supply for SYS.
+- vin-sm0-supply: The input supply for the SM0.
+- vin-sm1-supply: The input supply for the SM1.
+- vin-sm2-supply: The input supply for the SM2.
+- vinldo01-supply: The input supply for the LDO1 and LDO2
+- vinldo23-supply: The input supply for the LDO2 and LDO3
+- vinldo4-supply: The input supply for the LDO4
+- vinldo678-supply: The input supply for the LDO6, LDO7 and LDO8
+- vinldo9-supply: The input supply for the LDO9
+
+Optional properties:
+- ti,system-power-controller: Telling whether or not this pmic is controlling
+ the system power.
Each regulator is defined using the standard binding for regulators.
+Note: LDO5 and LDO_RTC is supplied by SYS regulator internally and driver
+ take care of making proper parent child relationship.
+
Example:
pmu: tps6586x@34 {
@@ -21,7 +41,25 @@ Example:
#gpio-cells = <2>;
gpio-controller;
+ ti,system-power-controller;
+
+ sys-supply = <&some_reg>;
+ vin-sm0-supply = <&some_reg>;
+ vin-sm1-supply = <&some_reg>;
+ vin-sm2-supply = <&some_reg>;
+ vinldo01-supply = <...>;
+ vinldo23-supply = <...>;
+ vinldo4-supply = <...>;
+ vinldo678-supply = <...>;
+ vinldo9-supply = <...>;
+
regulators {
+ sys_reg: sys {
+ regulator-name = "vdd_sys";
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
sm0_reg: sm0 {
regulator-min-microvolt = < 725000>;
regulator-max-microvolt = <1500000>;
diff --git a/Documentation/devicetree/bindings/regulator/twl-regulator.txt b/Documentation/devicetree/bindings/regulator/twl-regulator.txt
index 0c3395d55ac..658749b90b9 100644
--- a/Documentation/devicetree/bindings/regulator/twl-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/twl-regulator.txt
@@ -15,7 +15,6 @@ For twl6030 regulators/LDOs
- "ti,twl6030-vusb" for VUSB LDO
- "ti,twl6030-v1v8" for V1V8 LDO
- "ti,twl6030-v2v1" for V2V1 LDO
- - "ti,twl6030-clk32kg" for CLK32KG RESOURCE
- "ti,twl6030-vdd1" for VDD1 SMPS
- "ti,twl6030-vdd2" for VDD2 SMPS
- "ti,twl6030-vdd3" for VDD3 SMPS
diff --git a/Documentation/devicetree/bindings/regulator/vexpress.txt b/Documentation/devicetree/bindings/regulator/vexpress.txt
new file mode 100644
index 00000000000..d775f72487a
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/vexpress.txt
@@ -0,0 +1,32 @@
+Versatile Express voltage regulators
+------------------------------------
+
+Requires node properties:
+- "compatible" value: "arm,vexpress-volt"
+- "arm,vexpress-sysreg,func" when controlled via vexpress-sysreg
+ (see Documentation/devicetree/bindings/arm/vexpress-sysreg.txt
+ for more details)
+
+Required regulator properties:
+- "regulator-name"
+- "regulator-always-on"
+
+Optional regulator properties:
+- "regulator-min-microvolt"
+- "regulator-max-microvolt"
+
+See Documentation/devicetree/bindings/regulator/regulator.txt
+for more details about the regulator properties.
+
+When no "regulator-[min|max]-microvolt" properties are defined,
+the device is treated as fixed (or rather "read-only") regulator.
+
+Example:
+ volt@0 {
+ compatible = "arm,vexpress-volt";
+ arm,vexpress-sysreg,func = <2 0>;
+ regulator-name = "Cores";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-always-on;
+ };