When interrupts are disabled, an RX condition can occur but
it is not reported when enabling interrupts again. We need to check
RSR and use napi_reschedule() if condition is met.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Here is another handful of late-breaking fixes intended for the 3.8
stream... Hopefully the will still make it! :-)
There are three mac80211 fixes pulled from Johannes:
"Here are three fixes still for the 3.8 stream, the fix from Cong Ding
for the bad sizeof (Stephen Hemminger had pointed it out before but I'd
promptly forgotten), a mac80211 managed-mode channel context usage fix
where a downgrade would never stop until reaching non-HT and a bug in
the channel determination that could cause invalid channels like HT40+
on channel 11 to be used."
Also included is a mwl8k fix that avoids an oops when using mwl8k
devices that only support the 5 GHz band.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The original fix that was applied for setting gso_type required more change
than necessary because it was assumed ixgbe does RSC on IPv6 frames and this
is not correct. RSC is only supported with IPv4/TCP frames only. As such we
can simplify the fix and avoid the unnecessary move of eth_type_trans.
The previous patch "ixgbe: fix gso type" and this patch reduce the entire fix
to one line that sets gso_type to TCPV4 if the frame is RSC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In LRO mode, bnx2x set gso_size but not gso type.
This leads to crashes in macvtap.
Commit cbf1de72324a8105ddcc3d9ce9acbc613faea17e
queued for 3.9 includes a more complete fix.
This is a minimal patch to avoid the crash, for 3.8.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic set gso_size but not gso type. This leads to crashes
in macvtap.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe set gso_size but not gso_type. This leads to
crashes in macvtap.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch the stmmac fails in case of the phy device
is not found; w/o this fix the mdio can be register twice when
do down/up the iface and this is not correct.
Reported-by: Stas <stsp@list.ru>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the name of the macro used for
debugging the transmit process. I used STMMAC_TX_DEBUG
instead of STMMAC_XMIT_DEBUG.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert two power saving r8169 changes to fix some regressions
reported.
Reported-by: Jörg Otte <jrg.otte@gmail.com>
Tested-by: Jörg Otte <jrg.otte@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d64ec84151.
Jörg Otte reported his 8168evl to increase boot time link detection
from 1.6 to 10 s.
Hayes suggests reverting it for the time being.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Jörg Otte <jrg.otte@gmail.com>
This reverts commit e0c0755779.
Jörg Otte reported his 8168evl to fail boot time link detection.
Hayes suggests reverting it for the time being.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Jörg Otte <jrg.otte@gmail.com>
Pull networking fixes from David Miller:
1) Revert iwlwifi reclaimed packet tracking, it causes problems for a
bunch of folks. From Emmanuel Grumbach.
2) Work limiting code in brcmsmac wifi driver can clear tx status
without processing the event. From Arend van Spriel.
3) rtlwifi USB driver processes wrong SKB, fix from Larry Finger.
4) l2tp tunnel delete can race with close, fix from Tom Parkin.
5) pktgen_add_device() failures are not checked at all, fix from Cong
Wang.
6) Fix unintentional removal of carrier off from tun_detach(),
otherwise we confuse userspace, from Michael S. Tsirkin.
7) Don't leak socket reference counts and ubufs in vhost-net driver,
from Jason Wang.
8) vmxnet3 driver gets it's initial carrier state wrong, fix from Neil
Horman.
9) Protect against USB networking devices which spam the host with 0
length frames, from Bjørn Mork.
10) Prevent neighbour overflows in ipv6 for locally destined routes,
from Marcelo Ricardo. This is the best short-term fix for this, a
longer term fix has been implemented in net-next.
11) L2TP uses ipv4 datagram routines in it's ipv6 code, whoops. This
mistake is largely because the ipv6 functions don't even have some
kind of prefix in their names to suggest they are ipv6 specific.
From Tom Parkin.
12) Check SYN packet drops properly in tcp_rcv_fastopen_synack(), from
Yuchung Cheng.
13) Fix races and TX skb freeing bugs in via-rhine's NAPI support, from
Francois Romieu and your's truly.
14) Fix infinite loops and divides by zero in TCP congestion window
handling, from Eric Dumazet, Neal Cardwell, and Ilpo Järvinen.
15) AF_PACKET tx ring handling can leak kernel memory to userspace, fix
from Phil Sutter.
16) Fix error handling in ipv6 GRE tunnel transmit, from Tommi Rantala.
17) Protect XEN netback driver against hostile frontend putting garbage
into the rings, don't leak pages in TX GOP checking, and add proper
resource releasing in error path of xen_netbk_get_requests(). From
Ian Campbell.
18) SCTP authentication keys should be cleared out and released with
kzfree(), from Daniel Borkmann.
19) L2TP is a bit too clever trying to maintain skb->truesize, and ends
up corrupting socket memory accounting to the point where packet
sending is halted indefinitely. Just remove the adjustments
entirely, they aren't really needed. From Eric Dumazet.
20) ATM Iphase driver uses a data type with the same name as the S390
headers, rename to fix the build. From Heiko Carstens.
21) Fix a typo in copying the inner network header offset from one SKB
to another, from Pravin B Shelar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (56 commits)
net: sctp: sctp_endpoint_free: zero out secret key data
net: sctp: sctp_setsockopt_auth_key: use kzfree instead of kfree
atm/iphase: rename fregt_t -> ffreg_t
net: usb: fix regression from FLAG_NOARP code
l2tp: dont play with skb->truesize
net: sctp: sctp_auth_key_put: use kzfree instead of kfree
netback: correct netbk_tx_err to handle wrap around.
xen/netback: free already allocated memory on failure in xen_netbk_get_requests
xen/netback: don't leak pages on failure in xen_netbk_tx_check_gop.
xen/netback: shutdown the ring if it contains garbage.
net: qmi_wwan: add more Huawei devices, including E320
net: cdc_ncm: add another Huawei vendor specific device
ipv6/ip6_gre: fix error case handling in ip6gre_tunnel_xmit()
tcp: fix for zero packets_in_flight was too broad
brcmsmac: rework of mac80211 .flush() callback operation
ssb: unregister gpios before unloading ssb
bcma: unregister gpios before unloading bcma
rtlwifi: Fix scheduling while atomic bug
net: usbnet: fix tx_dropped statistics
tcp: ipv6: Update MIB counters for drops
...
Ian Campbell says:
====================
The Xen netback implementation contains a couple of flaws which can
allow a guest to cause a DoS in the backend domain, potentially
affecting other domains in the system.
CVE-2013-0216 is a failure to sanity check the ring producer/consumer
pointers which can allow a guest to cause netback to loop for an
extended period preventing other work from occurring.
CVE-2013-0217 is a memory leak on an error path which is guest
triggerable.
The following series contains the fixes for these issues, as previously
included in Xen Security Advisory 39:
http://lists.xen.org/archives/html/xen-announce/2013-02/msg00001.html
Changes in v2:
- Typo and block comment format fixes
- Added stable Cc
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Matthew Daley <mattjd@gmail.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A buggy or malicious frontend should not be able to confuse netback.
If we spot anything which is not as it should be then shutdown the
device and don't try to continue with the ring in a potentially
hostile state. Well behaved and non-hostile frontends will not be
penalised.
As well as making the existing checks for such errors fatal also add a
new check that ensures that there isn't an insane number of requests
on the ring (i.e. more than would fit in the ring). If the ring
contains garbage then previously is was possible to loop over this
insane number, getting an error each time and therefore not generating
any more pending requests and therefore not exiting the loop in
xen_netbk_tx_build_gops for an externded period.
Also turn various netdev_dbg calls which no precipitate a fatal error
into netdev_err, they are rate limited because the device is shutdown
afterwards.
This fixes at least one known DoS/softlockup of the backend domain.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix mlx4 VFs not working on old guests because of 64B CQE changes
- Fix ill-considered sparse fix for qib
- Fix IPoIB crash due to skb double destruct introduced in 3.8-rc1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bmKU
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull IB regression fixes from Roland Dreier:
- Fix mlx4 VFs not working on old guests because of 64B CQE changes
- Fix ill-considered sparse fix for qib
- Fix IPoIB crash due to skb double destruct introduced in 3.8-rc1
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: Fix for broken sparse warning fix
mlx4_core: Fix advertisement of wrong PF context behaviour
IPoIB: Fix crash due to skb double destruct
Adding new class/subclass/protocol combinations based on the GPLed
out-of-tree Huawei driver. One of these has already appeared on a
device labelled as "E320".
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a new vendor specific class/subclass/protocol combination
for CDC NCM devices based on information from a GPLed out-of-tree
driver from Huawei.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 08ff32352d ("mlx4: 64-byte CQE/EQE support") introduced a
regression where older guest VF drivers failed to load even when
64-byte EQEs/CQEs are disabled, since the PF wrongly advertises the
new context behaviour anyway. The failure looks like:
mlx4_core 0000:00:07.0: Unknown pf context behaviour
mlx4_core 0000:00:07.0: Failed to obtain slave caps
mlx4_core: probe of 0000:00:07.0 failed with error -38
Fix this by basing this advertisement on dev->caps.flags, which is the
operational capabilities used by the QUERY_FUNC_CAP command wrapper
(dev_cap->flags holds the firmware capabilities).
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch addresses a long standing issue of the driver with the
mac80211 .flush() callback. Since implementing the .flush() callback
a number of issues have been fixed, but a WARN_ON_ONCE() was still
triggered because the timeout on the flush could still occur.
This patch changes the awkward design using msleep() into one using
a waitqueue. The waiting flush() context will kick the transmit dma
when it is idle and the timeout used waiting for the event is set
to 500 ms. Worst case there can be 64 frames outstanding for transmit
in the driver. At a rate of 1Mbps that would take 1.5 seconds assuming
MTU is 1500 bytes and ignoring retries. The WARN_ON_ONCE() is also
removed as this was put in to indicate the flush timeout as a reason
for the driver to stall. That was not happening since fixing endless
AMPDU retries with following upstream commit:
commit 85091fc0a7
Author: Arend van Spriel <arend@broadcom.com>
Date: Thu Feb 23 18:38:22 2012 +0100
brcm80211: smac: fix endless retry of A-MPDU transmissions
bugzilla: 42840 <https://bugzilla.kernel.org/show_bug.cgi?id=42840>
bugzilla@redhat: <https://bugzilla.redhat.com/show_bug.cgi?id=799168>
bugzilla@redhat: <https://bugzilla.redhat.com/show_bug.cgi?id=787649>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Camaleón <noelamac@gmail.com>
Cc: Milan Bouchet-Valat <nalimilan@club-internet.fr>
Cc: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kernel commits 41affd5 and 6539306 changed the locking in rtl_lps_leave()
from a spinlock to a mutex by doing the calls indirectly from a work queue
to reduce the time that interrupts were disabled. This change was fine for
most systems; however a scheduling while atomic bug was reported in
https://bugzilla.redhat.com/show_bug.cgi?id=903881. The backtrace indicates
that routine rtl_is_special(), which calls rtl_lps_leave() in three places
was entered in atomic context. These direct calls are replaced by putting a
request on the appropriate work queue.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-and-tested-by: Nathaniel Doherty <ntdoherty@gmail.com>
Cc: Nathaniel Doherty <ntdoherty@gmail.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is normal for minidrivers accumulating frames to return NULL
from their tx_fixup function. We do not want to count this as a
drop, or log any debug messages. A different exit path is
therefore chosen for such drivers, skipping the debug message
and the tx_dropped increment.
The test for accumulating drivers was however completely bogus,
making the exit path selection depend on whether the user had
enabled tx_err logging or not. This would arbitrarily mess up
accounting for both accumulating and non-accumulating minidrivers,
and would result in unwanted debug messages for the accumulating
drivers.
Fix by testing for FLAG_MULTI_PACKET instead, which probably was
the intention from the beginning. This usage match the documented
behaviour of this flag:
Indicates to usbnet, that USB driver accumulates multiple IP packets.
Affects statistic (counters) and short packet handling.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
here's a patch for net for the v3.8 release cycle. Alexander Stein noticed that
the c_can hardware has a fixed bit in the IFx_MASK2 register. His patch fixes
writing of this register by always setting this bit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
1) rhine_tx() should use dev_kfree_skb() not dev_kfree_skb_irq()
2) rhine_slow_event_task's NAPI triggering logic is racey, it
should just hit the interrupt mask register. This is the
same as commit 7dbb491878
("r8169: avoid NAPI scheduling delay.") made to fix the same
problem in the r8169 driver. From Francois Romieu.
Reported-by: Jamie Gloudon <jamie.gloudon@gmail.com>
Tested-by: Jamie Gloudon <jamie.gloudon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to C_CAN documentation, the reserved bit in IFx_MASK2 register is
fixed 1.
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add VID, PID and fixed interface for Telit LE920
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A device sending 0 length frames as fast as it can has been
observed killing the host system due to the resulting memory
pressure.
Temporarily disable RX skb allocation and URB submission when
the current error ratio is high, preventing us from trying to
allocate an infinite number of skbs. Reenable as soon as we
are finished processing the done queue, allowing the device
to continue working after short error bursts.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A scan request is split into multiple scan commands queued in
scan_pending_q. Each scan command will be sent to firmware and
its response is handlded one after another.
If any error is detected while parsing IE in command response
buffer the remaining data will be ignored and error is returned.
We should check if there is any more scan commands pending in
the queue before returning error. This ensures that we will call
cfg80211_scan_done if this is the last scan command, or send
next scan command in scan_pending_q to firmware.
Cc: "3.6+" <stable@vger.kernel.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
vmxnet3 fails to set netif_carrier_off on probe, meaning that when an interface
is opened the __LINK_STATE_NOCARRIER bit is already cleared, and so
/sys/class/net/<ifname>/operstate remains in the unknown state. Correct this by
setting netif_carrier_off on probe, like other drivers do.
Also, while we're at it, lets remove the netif_carrier_ok checks from the
link_state_update function, as that check is atomically contained within the
netif_carrier_[on|off] functions anyway
Tested successfully by myself
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare instances, memory errors have been detected in the internal packet
buffer memory on I217/I218 when stressed under certain environmental
conditions. Enable Error Correcting Code (ECC) in hardware to catch both
correctable and uncorrectable errors. Correctable errors will be handled
by the hardware. Uncorrectable errors in the packet buffer will cause the
packet to be received with an error indication in the buffer descriptor
causing the packet to be discarded. If the uncorrectable error is in the
descriptor itself, the hardware will stop and interrupt the driver
indicating the error. The driver will then reset the hardware in order to
clear the error and restart.
Both types of errors will be accounted for in statistics counters.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: <stable@vger.kernel.org> # 3.5.x & 3.6.x
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bonding module is loaded with primary parameter and one decides to unset
primary slave using sysfs these settings are not preserved during bond device
restart. Primary slave is only unset once and it's not remembered in
bond->params structure. Below is example of recreation.
grep OPTS /etc/sysconfig/network-scripts/ifcfg-bond0
BONDING_OPTS="mode=active-backup miimon=100 primary=eth01"
grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: eth01 (primary_reselect always)
echo "" > /sys/class/net/bond0/bonding/primary
grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: None
sed -i -e 's/primary=eth01//' /etc/sysconfig/network-scripts/ifcfg-bond0
grep OPTS /etc/sysconfig/network-scripts/ifcfg-bond
BONDING_OPTS="mode=active-backup miimon=100 "
ifdown bond0 && ifup bond0
without patch:
grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: eth01 (primary_reselect always)
with patch:
grep "Primary Slave" /proc/net/bonding/bond0
Primary Slave: None
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Milos Vyletel <milos.vyletel@sde.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We forbid polling, writing and reading when the file were detached, this may
complex the user in several cases:
- when guest pass some buffers to vhost/qemu and then disable some queues,
host/qemu needs to do its own cleanup on those buffers which is complex
sometimes. We can do this simply by allowing a user can still write to an
disabled queue. Write to an disabled queue will cause the packet pass to the
kernel and read will get nothing.
- align the polling behavior with macvtap which never fails when the queue is
created. This can simplify the polling errors handling of its user (e.g vhost)
We can simply achieve this by don't assign NULL to tfile->tun when detached.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c8d68e6be1 removed carrier off call
from tun_detach since it's now called on queue disable and not only on
tun close. This confuses userspace which used this flag to detect a
free tun. To fix, put this back but under if (clean).
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Tested-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In routine _rtl_rx_pre_process(), skb_dequeue() is called to get an skb;
however, the wrong variable name is used in subsequent calls.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This issue was reported on the wireless list (see [1]) in which
brcmsmac ran into a fatal error:
[ 588.284074] brcmsmac bcma0:0: frameid != txh->TxFrameID
[ 588.284098] brcmsmac bcma0:0: MI_TFS: fatal
[ 588.284103] brcmsmac bcma0:0: wl0: fatal error, reinitializing
[ 588.286208] ieee80211 phy0: Hardware restart was requested
The tx status feedback is processed in a loop limiting the number of
frames processed in one run. The code terminate processing when the
limit is reached regardless the txstatus value read from the device
register. When that status is is flagged as being valid it must be
processed as the hardware will clear it after is has been read.
Bisecting was done by Seth Forshee and showed following commit as the
culprit:
commit 57fe504817
Author: Piotr Haber <phaber@broadcom.com>
Date: Wed Nov 28 21:44:07 2012 +0100
brcmsmac: fix bounds checking in tx/rx
[1] http://www.spinics.net/lists/linux-wireless/msg101293.html
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dm9620 is a newer variant of dm9601 with more features (usb 2.0, checksum
offload, ..), but it can also be put in a dm9601 compatible mode, allowing
us to reuse the existing driver.
This does mean that the extended features like checksum offload cannot be
used, but that's hardly critical on a 100mbps interface.
Thanks to Sławek Wernikowski <slawek@wernikowski.net> for providing me
with a dm9620 based device to test.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the setting of the INTR pin that is
valid for IP101 A/G device and not for the IP1001.
Reported-by: Anunay Saxena <anunay.saxena@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like several other PHY devices which support RGMII, the IC+1001 allows
additional delays to by added to the RX_CLK and TX_CLK signals to
compensate for skew between the clock and data signals. Previously this
was always enabled, but this change makes use of the different RGMII
interface modes to allow the user to specify whether this should be
enabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Control of receive descriptor must not be returned to ethernet chipset
before vlan tag processing is done.
VLAN tag receive word is now reset both in normal and error path.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Spotted-by: Timo Teras <timo.teras@iki.fi>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 9992c2e (net: cdc_ncm: workaround for missing CDC Union)
added code to lookup an IAD for the interface we are probing.
This is redundant. The USB core has already done the lookup
and saved the result in the USB interface struct. Use that
instead.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Ferre